ALI JAHJAH

Dr. ALI JAHJAH

orcid

Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
19 June 2024 in Journal of Stomatology Oral and Maxillofacial Surgery
Verified
Journal Article
Closed access
Maurizio D'AmarioMaurizio D'Amario
Maurizio D'Amario
AOAlessandro Orsijena
Alessandro Orsijena
Rocco FrancoRocco Franco
Rocco Franco
MCMarianna Chiacchia
Marianna Chiacchia
AJALI JAHJAH
ALI JAHJAH
MCMario Capogreco
Mario Capogreco

10 June 2024 in Prosthesis
Verified
Journal Article
Open access
PDF file
Francesco De AngelisFrancesco De Angelis
Francesco De Angelis
Maurizio D'AmarioMaurizio D'Amario
Maurizio D'Amario
AJALI JAHJAH
ALI JAHJAH
MFMassimo Frascaria
Massimo Frascaria
MVMirco Vadini
Mirco Vadini
CDCamillo D'Arcangelo
Camillo D'Arcangelo
To evaluate the flexural strength and flexural modulus of three recently introduced 3D-Printed resins and compare them with the flexural properties of other well known, already commercialized, and extensively used resin based dental materials. Three 3D-printed dental resins, a fiber-reinforced epoxy resin, a heat-cured bis-acrylate-based composite resin, two conventional CAD/CAM PMMA, and a graphene-reinforced CAD/CAM PMMA, were selected for this study. Ten prismatic-shaped specimens (2 × 2 × 25 mm) were fabricated for each material (n = 10). All specimens underwent a three-point bending test using a universal testing machine and were loaded until fracture. Flexural strength (MPa) and flexural modulus (MPa) mean values were calculated and compared using the on ranks One-Way ANOVA test. Scanning electron microscope analysis of the 3D-printed resins was performed. Significantly different flexural properties were recorded among the tested materials. The fiber-reinforced epoxy resin exhibited the highest flexural strength (418.0 MPa) while, among the 3D-printed resins, the best flexural strength was achieved by Irix-Max (135.0 MPa). Irix-Plus and Temporis led to the lowest mean flexural strength values (103.9 MPa and 101.3 MPa, respectively) of all the CAD/CAM milled materials, except for the conventional PMMA by Sintodent (88.9 MPa). The fiber-reinforced epoxy resin also showed the highest flexural modulus (14,672.2 MPa), followed by the heat-cured bis-acrylate composite (10,010.1 MPa). All 3D-printed resins had a higher flexural modulus than the conventional PMMA materials. CAD/CAM fiber-reinforced epoxy resin excels in flexural strength, with Irix-Max showing promising flexural properties, which could encourage its use for permanent restorations. Caution is needed with Irix-Plus and Temporis due to their lower flexural strength compared to other traditional materials.

24 November 2025 in Applied Sciences
Verified
Journal Article
Open access
PDF file
Maurizio D'AmarioMaurizio D'Amario
Maurizio D'Amario
EVElena Vitocco
Elena Vitocco
AJALI JAHJAH
ALI JAHJAH
ACAntonio Capogreco
Antonio Capogreco
SMStefania Mauro
Stefania Mauro
Francesco De AngelisFrancesco De Angelis
Francesco De Angelis
This study aimed to investigate adhesive techniques applied to MIH-affected teeth by analyzing the one-year failure rate of restorations performed using total-etch and self-etch adhesive methods. This systematic review was conducted in accordance with the PRISMA 2020 statement. Eligibility criteria were defined using the PICO acronym. In vivo studies published from 2017 onward were evaluated. Two independent reviewers conducted the search on PubMed, Scopus, Cochrane, and Web of Science. The risk of bias was assessed with RoB2 and the Newcastle-Ottawa Scale. Statistical analysis was performed using the Open Meta [Analyst] software based on the absolute risk of failure. Results were presented as a pooled estimate with a 95% confidence interval (CI) and visualized in forest plots. Four RCTs and one retrospective cohort study were selected for the analysis. Data collected included information such as authors, study design, age, restorations, degree of hypomineralization, protocol, and follow-up. The meta-analysis showed no statistically significant differences between the techniques (p = 0.338) on MIH-affected teeth. This meta-analysis supports the use of both adhesive techniques for managing MIH teeth, emphasizing the need for further studies to examine the specific clinical and technical conditions under which each technique might be more advantageous.