Loading and contact stress distribution on the thread teeth in tubing and casing premium threaded connections are of great importance for design optimization, pretightening force control, and thread failure prevention. This paper proposes an analytical method based on the elastic mechanics. This is quite different from other papers, which mainly rely on finite element analysis. The differential equation of load distribution on the thread teeth was established according to equal pitch of the engaged thread after deformation and solved by finite difference method. Furthermore, the relation between load acting on each engaged thread and mean contact stress on its load flank is set up based on the geometric description of thread surface. By comparison, this new analytical method with the finite element analysis for a modified API 177.8 mm premium threaded connection is approved. Comparison of the contact stress on the last engaged thread between analytical model and FEM shows that the accuracy of analytical model will decline with the increase of pretightening force after the material enters into plastic deformation. However, the analytical method can meet the needs of engineering to some extent because its relative error is about 6.2%~18.1% for the in‐service level of pretightening force.
The present investigations on sealability evaluation for tubing and casing premium connections depend on the FEM with testing. This paper proposed a theoretical model to evaluate the sealability of a sphere-type premium connection based on make-up torque, which combines Hertz contact pressure and the von Mises yield criterion for calculating elastic–plastic contact pressure distribution on sealing interface and adopts the gas sealing criterion obtained from Murtagian’s experimental results for deducing gas sealing capacity. With the proposed model, the effects of additional make-up torque from the sealing interface on the sealing contact pressure distribution and key sealability parameters, including contact width, yield width, average contact pressure and gas sealing capacity, were analyzed and compared. The results show that additional make-up torque from the sealing interface closely influenced sealability parameters’ variation and gas sealing capacity. The gas sealing index based on the sealing contact energy theory should be recommended for sealability evaluation other than average contact pressure on the sealing interface. For improving gas sealability, make-up torque should be controlled accurately for ensuring enough average contact pressure and contact width but a proper yield width, and a lager sphere radius should be selected for reducing the risk of yield sticking.
This paper proposed a semi-theoretical model to quantitatively predict leakage rate of tubing and casing premium connections. The geometric parameters of the sealing surface profile approximated by a sinusoidal micro-convex surface were first obtained based on the random normal distribution sampling method. With the actual area prediction formula for elastic–plastic contact of an axisymmetric sinusoidal micro-convex body based on the equivalent simulation principle, the circumferential leakage width and radial average leakage height of the micro-leakage channel between sealing surfaces were then acquired with the surface roughness and geometric mean contact pressure. At last, the actual micro-leakage rate of the premium connection was derived by considering the non-uniform contact pressure distribution between sealing surfaces. An example was investigated to validate the model and reveal the sealing and leakage characteristics, and anti-leakage measures were proposed. The results show that average contact pressure, circumferential leakage width, and radial average leakage height between sealing surfaces were non-uniformly distributed. The leakage rate of a premium connection decreases exponentially with an increase in radial interference between sealing surfaces. In order to reduce leakage rate, it is beneficial to increase radial interference and lower sealing surface roughness.
Drilling is a key step in the exploitation of deep oil and gas resources. In order to clarify the stress state of the rocks and the mechanism of rock breakage in deep-well drilling, a thermal-hydro-mechanical coupling model for deep-well drilling was established, and the effects of drilling on the temperature, pressure, and stress in the formation were studied. Furthermore, the effects of the formation parameters and wellbore parameters on the bottomhole stress were analyzed. The results revealed that after the formation was drilled, the temperatures in different horizontal in situ stress directions were not significantly different, but the difference in the pore pressure between the maximum and minimum horizontal stress directions was large. The average effective stress at the bottom of the hole was the smallest, and in some areas, it was tensile stress. For deep-well drilling, as the formation pressure increased, the in situ stress increased, and the permeability decreased, leading to greater average effective stress of the bottomhole rock. As a result, it was harder to break the rock, and the drilling efficiency decreased. Reducing the wellbore pressure and wellbore temperature is conducive to forming tensile stress near the borehole axis in the bottomhole, causing tensile damage. The average effective stress of the formation near the shoulder of the drill bit was compressive stress, and it is advisable to take advantage of the rock shear failure characteristics to improve the drilling efficiency in this area. The results of this study can help us to understand the stress state of the bottomhole rocks and the mechanism of rock breakage and can provide a reference for the optimization of drilling tools and drilling parameters in deep-well drilling.
24 February 2020 in Mathematical Problems in Engineering
The present research studies about sealability of premium connection almost focus on qualitative description by sealing contact stress distribution, which is not convenient for sealing capacity evaluation and sealing parameter design. This paper proposes a quantitative model to calculate directly gas sealing capacity of cone to cone premium connection, different from the usual finite element method with testing, which combines the elastic thick wall cylinder interference fit theory for calculating sealing stress with the gas sealing criterion obtained from Murtagian’s experimental results. With the proposed model, the effects of pipe wall thickness, seal cone taper, radial sealing interference, and axial sealing length on the gas sealing capacity have been investigated. Furthermore, the gas sealing capacity envelope curve based on radial sealing interference and axial sealing length is also calculated and a new sealing parameter design method is proposed for cone to cone premium connection. The results show that the internal upset pipe is good for sealability, and increasing both radial sealing interference and axial sealing length can significantly enhance gas sealability while seal cone taper has an unobvious effect on it. To meet sealing capacity, the designed sealing parameter combination (δd, Ld) should be located in the upper right region of the gas sealing capacity envelope curve.
The abnormal swab pressure resulting from packer unsetting poses a great threat to the collapse resistance of production casings in deep high-pressure and high-temperature (HPHT) oil wells. This paper proposes an analytical model to predict the transient swab pressure in the A-annulus after packer unsetting based on a U-type tube and an iterative method. The model can further evaluate the collapse failure risk of the production casing in the whole wellbore. An example study and sensitivity analysis were carried out to reveal the variation characteristics of the transient swab pressure in the A-annulus and the failure risk of the production casing after packer unsetting. Furthermore, some preventative measures are proposed. The largest swab pressure occurs at the initial time of packer unsetting, which will lead to sudden collapse failure of the deeper production casing. A smaller width of the annular clearance between the packer rubber and production casing and a larger initial liquid level depth in the A-annulus can reduce the swab pressure in the A-annulus after packer unsetting and collapse failure risk of the production casing. In the example, when the width of the annular clearance decreased from 2.97 to 2 mm, the maximum swab pressure decreased from 88.71 to 27.4 MPa, a decrease of 69.1%. When the initial liquid level depth in the A-annulus increased from 700 to 900 m, the maximum swab pressure decreased from 122 to 57.05 MPa, a decrease of 53.2%. When the width of annular clearance was 2.97 mm, the collapse resistance safety factors for the production casing were less than 1.1 and may suffer from collapse failure for well depth between 3610 m and 6100 m. When the initial liquid level depth in the A-annulus was 700 m, the production casing will suffer from collapse failure for well depth between 2869 m and 6100 m. When the width of the annular clearance was less than 2.5 mm and the initial liquid level depth in the A-annulus was larger than 900 m, the collapse resistance safety factors for the production casing were all greater than 1.1 and the whole production casing was safe. To lower the collapse failure risk of the production casing because of packer unsetting, a packer rubber with a reasonable larger outer diameter and good deformation recovery ability is recommended, and the initial liquid level depth in the A-annulus should be controlled reasonably. The research results are of great significance for preventing the collapse failure of production casings during packer unsetting.