A new -band high-power rotating mode SLAC energy doubler (SLED)-type rf pulse compressor is proposed. It is based on a novel cavity type, a single open bowl-shaped energy storage cavity with high-quality factor and compact size, which is coupled to the waveguide using a compact rotating mode launcher. The novel cavity type is applied to the rf pulse compression system of the main linac rf module of the klystron-based option of the Compact Linear Collider. Quasispherical rotating modes of and are proposed for the correction cavity and storage cavity of the rf pulse compression system, respectively. The storage cavity working at has a quality factor above 240 000 and a diameter less than 33 cm. The design of the pulse compressor and in particular of the high-Q cavity will be presented in detail.
Nb3Sn is emerging as one of the focal points in superconducting radio frequency (SRF) research, owing to its excellent superconducting properties. These properties hold significant possibilities for cost reduction and the miniaturization of accelerators. In this paper, we report the recent efforts of the Shanghai Advanced Research Institute (SARI) in fabricating high-performance Nb3Sn superconducting cavities using the vapor diffusion method. This includes the construction of a Nb3Sn coating system with dual evaporators and the test results of 1.3 GHz single-cell coated cavities. The coated samples were characterized, and the growth state of the Nb3Sn films was analyzed. The first coated superconducting cavity was tested at both 4.4 K and 2 K, with different cooldown rates passing through the Nb3Sn critical temperatures. The causes of Sn droplet spot defect formation on the surface of the first cavity were analyzed, and such defects were eliminated in the coating of the second cavity by controlling the evaporation rate. This study provides a reference for the preparation of high-performance Nb3Sn-coated cavities using the vapor diffusion method, including the setup of the coating system, the comprehension of the vapor diffusion process, and the test conditions.
1 March 2007 in Journal of Magnetism and Magnetic Materials
Electropolishing (EP) has become a standard procedure for treating the inner surfaces of superconducting radio-frequency (SRF) cavities composed of pure niobium. In this study, a new EP facility was employed for the surface treatment of both 1.3 GHz and 3.9 GHz single-cell cavities at the Wuxi Platform. The stable “cold EP” mode was successfully implemented on this newly designed EP facility. By integrating the cold EP process with a two-step baking approach, a maximum accelerating gradient exceeding 40 MV/m was achieved in 1.3 GHz single-cell cavities. Additionally, an update to this EP facility involved the design of a special cathode system for small-aperture structures, facilitating the cold EP process for 3.9 GHz single-cell cavities. Ultimately, a maximum accelerating gradient exceeding 25 MV/m was attained in the 3.9 GHz single-cell cavities after undergoing the cold EP treatment. The design and commissioning of the EP device, as well as the electropolishing and vertical test results of the single-cell cavities, will be detailed herein. These methods and experiences are also transferable to multi-cell cavities and elliptical cavities of other frequencies.
Superconducting radio-frequency (SRF) cavities are widely used in particle accelerator facilities. The SRF-based energy recovery linac (ERL) equipped with special SRF cavities offers feasibility for application in high-power free electron lasers (FELs). This study aims to design and optimize a 3-cell cavity that serves as the accelerating structure for a 10 mA class injector of high-brightness ERL-FEL. We apply the middle-cell shape of the mature TESLA cavity, and the end-groups are optimized for high-current beam operation. The cavity is designed with two fundamental power coupler (FPC) ports, which enable high-power input by two FPCs. In addition, the beam pipe is enlarged to damp potentially strong higher-order modes (HOMs) induced by the high current beams. A multi-objective genetic algorithm is utilized to optimize the cavity geometry. The damping of HOMs, multipacting, and mechanical issues are also investigated to verify the rationality of the cavity design.