A solid-state cold-spray technique was employed for depositing the copper-coated graphite reinforced copper-based composite coatings on aluminum alloy 6061 T6 substrate under different process parameters. The optimum process parameters of the cold-sprayed coatings were predicted in terms of surface roughness, thickness and adhesion. The surface roughness was measured using a 3D profilometer, the thickness and element constitution were detected by an optical microscope and scanning electron microscope furnished with an energy-dispersive spectral analyzer and the adhesion was detected by the scratch test method. The microstructures of the deposited coatings were also observed by a scanning electron microscope. The results show that when the coating is not oxidized and dense, the copper-coated graphite reinforced copper-based composite coating at 800 °C, 5.5 MPa, possesses the lowest surface roughness, the maximum thickness and the highest adhesion among the cold-sprayed coatings. In addition, the surface roughness, thickness and adhesion of the deposited coatings are all linear with particle velocity.

Copper-coated graphite and copper mixture powders were deposited on AZ31B magnesium alloy and 6061 T6 aluminum alloy substrates under different process parameters by a solid-state cold spray technique. The microstructure of the copper-coated graphite and copper composite coatings was visually examined using photographs taken with an optical microscope and a scanning electron microscope. The surface roughness of the coatings was investigated with a 3D profilometer. The thickness of the coatings was determined through the analysis of the microstructure images, while the adhesion of the coatings was characterized using the scratch test method. The results indicate that the surface roughness of the coatings sprayed on the two different substrates gradually decreases as gas temperature and gas pressure increase. Additionally, the thickness and adhesion of the coatings deposited on the two different substrates both increase with an increase in gas temperature and gas pressure. Comparing the surface roughness, thickness, and adhesion of the coatings deposited on the two different substrates, the surface roughness and adhesion of the coatings on the soft substrate are greater than those of the coatings on the hard substrate, while the thickness of the coatings is not obviously affected by the hardness of the substrate. Furthermore, it is noteworthy that the surface roughness, thickness, and adhesion of the copper-coated graphite and copper composite coatings sprayed on the two different substrates exhibit a distinct linear relationship with particle velocity.

The development process of electrospark deposition (ESD) technology is reviewed, and the principles and differences of ESD technology are discussed in this review. Based on the research status regarding the ESD of titanium alloys, the promotion effect of ESD technology on wear resistance, corrosion resistance, oxidation resistance at high temperatures, and the biocompatibility of titanium alloys was elaborated on. For example, with the use of ESD technology to prepare Ti–Al, TiN, Ni–Cr, and other hardening coatings with high hardness, the maximum hardness of the deposited layer is six times higher than that of the substrate material, which greatly reduces the loss of the material surface in the process of friction in service, and has a high wear–resistance effect. The preparation of a single–phase lamellar coating is more beneficial for improving the oxidation resistance of the substrate. Carbide and a nano–porous coating can effectively enhance the bone integration ability of implants and promote biocompatibility. The application of ESD technology in the surface modification of titanium alloys is reviewed in detail. Finally, the development direction of ESD technology for titanium alloys is proposed.

Cold spray technology, as an emerging surface engineering technique, effectively prepares hard coatings by high-speed projection of powder materials onto substrates at relatively low temperatures. The principal advantage of this technology lies in its ability to rapidly deposit coatings without significantly altering the properties of the substrate or powder materials. Carbon-based materials, especially carbides and diamond, etc., are renowned for their exceptional hardness and thermal stability, which make them indispensable in industrial applications requiring materials with high wear resistance and durability at elevated temperatures. This review elucidates the fundamental principles of cold spray technology, the key components of the equipment, and the properties and applications of hard coatings. The equipment involved primarily includes spray guns, powder feeders, and gas heaters, while the properties of the coatings, such as mechanical strength, corrosion resistance, and tribological performance, are discussed in detail. Moreover, the application of this technology in preparing metal matrix composite (MMC) materials with carbon-based reinforcements, including tungsten carbide, boron carbide, titanium carbide, and diamond, are particularly emphasized, showcasing its potential to enhance the performance of tools and components. Finally, this article outlines the challenges and prospects faced by cold spray technology, highlighting the importance of material innovation and process optimization. This review provides researchers in the fields of materials science and engineering with a comprehensive perspective on the application of cold spray technology in MMC materials with carbon-based reinforcements to drive significant improvements in coating performance and broaden the scope of its industrial applications.

Ag-Sn-In-Ni-Te alloy ingots were produced through a heating–cooling combined mold continuous casting technique; they were then drawn into wires. However, during the drawing process, the alloy wires tended to harden, making further diameter reduction challenging. To overcome this, heat treatment was necessary to soften the previously drawn wires. The study investigated how variations in heat treatment temperature and holding time affected the microstructure, microhardness and corrosion resistance of the alloy wires. The results indicate that the alloy wires subjected to heat treatment at 700 °C for 2 h not only exhibited a uniform microstructure distribution, but also demonstrated low microhardness and excellent corrosion resistance.

In this article, the studies undertaken on brazed diamond tools were reviewed. The influences of the brazing alloys with different active elements on the brazing quality of brazed diamond tools are emphatically discussed. The differences in the micromorphology, friction and wear properties, and mechanical properties of brazed diamonds caused by three different brazing alloys are described in detail. The quality evaluation of brazed diamond tools is discussed from several aspects, such as the difference in microstructure of the diamond/brazing alloy interface, the friction and wear of brazed diamond tools, and the strength and residual stress of the brazing interface. Finally, relevant open questions related to the brazed diamond tools’ performance are outlined, and the future has been prospected.