Mahir Abrar

Mr. Mahir Abrar

orcid

Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
10 April 2025 in Journal of Electronic Materials
Verified
Journal Article
Open access
PDF file
MAMahir Abrar
Mahir Abrar
IBIshrat Jahan Biswas
Ishrat Jahan Biswas
DHDeidra Hodges
Deidra Hodges
Halide perovskite solar cells have garnered significant attention as one of the most rapidly advancing technologies in the field of photovoltaics (PV). In 2009, hybrid organic–inorganic halide perovskites achieved an initial power conversion efficiency (PCE) of 3.8%, with CH3NH3PbI3 serving as a photosensitizer in dye-sensitized solar cells. Recently, perovskite solar cells have attained a National Renewable Energy Laboratory (NREL)-certified record efficiency of 27%. However, the widespread adoption of lead-based perovskite solar cells (PSCs) is limited by the toxicity of lead (Pb) and their inherent stability challenges. To address these issues, researchers are focusing on lead-free alternatives that maintain high efficiency while improving stability. Pb-free double perovskite solar cells (DPSCs) have gained attention due to their promising performance, cost-effectiveness, and superior stability. This study explores the use of the nontoxic inorganic material Cs2AgInBr6 as the absorber layer in a DPSC, using SCAPS-1D software for simulation. The impact of different electron transport layers (ETLs), including zinc selenide (ZnSe) and tungsten disulfide (WS2), and hole transport layers (HTLs) including copper barium thiostannate (CBTS), methylammonium tin(II) bromide (MASnBr3), and cuprous oxide (Cu2O) on photovoltaic performance metrics, including power conversion efficiency, fill factor, and overall operational performance was analyzed. The results indicate that, with an optimal absorber layer thickness of 600 nm, the FTO/ZnSe/Cs2AgInBr6/MASnBr3/Ag device achieves a peak efficiency of 26.64%, attributed to its high open-circuit voltage of 1.1562 V, short-circuit current density of 27.494343 mA/cm2, and fill factor of 83.79% under a standard solar spectrum at air mass (AM) 1.5 and 300 K.

2 June 2024 in Nanomaterials
Verified
Journal Article
Open access
PDF file
MRMelorina Dolafi Rezaee
Melorina Dolafi Rezaee
BDBiplav Dahal
Biplav Dahal
JWJohn Watt
John Watt
MAMahir Abrar
Mahir Abrar
DHDeidra R. Hodges
Deidra R. Hodges
WLWenzhi Li
Wenzhi Li
Single-walled carbon nanotube (SWCNT) thin films were synthesized by using a floating catalyst chemical vapor deposition (FCCVD) method with a low flow rate (200 sccm) of mixed gases (Ar and H2). SWCNT thin films with different thicknesses can be prepared by controlling the collection time of the SWCNTs on membrane filters. Transmission electron microscopy (TEM) showed that the SWCNTs formed bundles and that they had an average diameter of 1.46 nm. The Raman spectra of the SWCNT films suggested that the synthesized SWCNTs were very well crystallized. Although the electrical properties of SWCNTs have been widely studied so far, the Hall effect of SWCNTs has not been fully studied to explore the electrical characteristics of SWCNT thin films. In this research, Hall effect measurements have been performed to investigate the important electrical characteristics of SWCNTs, such as their carrier mobility, carrier density, Hall coefficient, conductivity, and sheet resistance. The samples with transmittance between 95 and 43% showed a high carrier density of 1021–1023 cm−3. The SWCNTs were also treated using Brønsted acids (HCl, HNO3, H2SO4) to enhance their electrical properties. After the acid treatments, the samples maintained their p-type nature. The carrier mobility and conductivity increased, and the sheet resistance decreased for all treated samples. The highest mobility of 1.5 cm2/Vs was obtained with the sulfuric acid treatment at 80 °C, while the highest conductivity (30,720 S/m) and lowest sheet resistance (43 ohm/square) were achieved with the nitric acid treatment at room temperature. Different functional groups were identified in our synthesized SWCNTs before and after the acid treatments using Fourier-Transform Infrared Spectroscopy (FTIR).