Visualizing the near-field distribution of microwave field in a monopole antenna is very important for antenna design and manufacture. However, the traditional method of measuring antenna microwave near field distribution by mechanical scanning has some problems, such as long measurement time, low measurement accuracy and large system volume, which seriously limits the measurement effect of antenna microwave near field distribution. In this paper, a method of microwave near-field imaging of a monopole antenna using a nitrogen-vacancy center diamond is presented. We use the whole diamond as a probe and camera to achieve wide-field microwave imaging. Because there is no displacement structure in the system, the method has high time efficiency and good stability. Compared with the traditional measurement methods, the diamond probe has almost no effect on the measured microwave field, which realizes the accurate near-field imaging of the microwave field of the monopole antenna. This method achieves microwave near-field imaging of a monopole antenna with a diameter of 100 µm and a length of 15 mm at a field of view of 5 × 5 mm, with a spatial resolution of 3 µm and an imaging bandwidth of 2.7~3.2 GHz, and an optimal input microwave phase resolution of 0.52° at a microwave power of 0.8494 W. The results provide a new method for microwave near-field imaging and measurement of monopole antennas.

Optical sensing has attracted more and more attention in recent years with the advance in planar waveguide fabrication processes. The photon, as a carrier of information in sensing areas, could have a better performance than electrons. We propose a novel end-to-end ring cavity to fabricate sensitive units of a strain sensor. We then propose a method of combining a flexible substrate with an end-to-end semiconductor nanowire ring cavity to fabricate novel strain sensors. We used a tuning resonant wavelength detected by a homebuilt excitation and detection system to measure applied strain. The resonant wavelength of the strain gauge was red-shift and linear tuned with increasing strain. The gauge factor was about 50, calculated through experiments and theory, and Q was 1938, with structural parameters L = 70 µm and d = 1 µm. The high sensitivity makes it possible to measure micro deformation more accurately. End-to-end coupling active nanowire waveguides eliminate the shortcomings of side by side coupling structures, which have the phasing shift with no minor optical density loss. This resonator in flexible substrates could be used not only as on-chip strain sensors for micro or nano deformation detecting but also as tunable light sources for photonic integrated circuits.

Information security serves as the cornerstone for ensuring the stable development of today’s highly digitized era. As cryptographic primitives with high security and robust encryption capabilities, physical unclonable functions (PUFs) are recognized as one of the critical solutions to address information leakage issues. However, the encoding of PUFs often relies on the inherent properties of materials, which limits the potential for further enhancement of their encoding capacity (EC). In this study, we introduce a four-level encoding scheme by leveraging the stochastic characteristics of free radical chemical reactions and energy deposition in the fabrication process of silicon carbide (SiC) color centers. A multilevel multimodal PUF (MMPUF) encoding strategy (ES) for flexible substrates with high EC, low cost, and simple and fast readout was constructed. The spatially random distribution of SiC and silicon vacancy (V_si) color-center concentrations as well as the offsets of the laser pyrolysis position along the X- and Y-axes are four independent physical properties that ensure the encoding performance of the PUF, achieving a high encoding capacity of 2^4×10×10 and secure, stable, and unclonable encoding. Furthermore, the integration of the PUF tags with the products through a doping manufacturing process, rather than simple attachment, enhances the security and practicality of the anti-counterfeiting system. The proposed encoding hierarchy based on the offsets provides a novel encoding solution for improving PUF EC.

In this study, we established a passive direction-finding scheme based on microwave power measurement: Microwave intensity was detected using microwave-frequency proportion integration differentiation control and coherent population oscillation effect converting the change in microwave resonance peak intensity into a shift of the microwave frequency spectrum, for which the minimum microwave intensity resolution was −20 dBm. The direction angle of the microwave source was calculated using the weighted global least squares method of microwave field distribution. This lay in the 12~26 dBm microwave emission intensity range, and the measurement position was in the range of (−15°~15°). The average angle error of the angle measurement was 0.24°, and the maximum angle error was 0.48°. In this study, we established a microwave passive direction-finding scheme based on quantum precision sensing, which measures the microwave frequency, intensity, and angle in a small space and has a simple system structure, small equipment size, and low system power consumption. In this study, we provide a basis for the future application of quantum sensors in microwave direction measurements.

In this paper, a carbon nanotube (CNT)/polydimethylsiloxane (PDMS) composite force-sensitive structure with good flexibility is proposed and fabricated, and the measurement of scanning electron microscopy (SEM) and Raman are carried out. The equivalent circuit of force-sensitive test of structure is performed and analyzed under direct current (DC) and alternating current (AC) conditions. Under AC conditions, experimental results further show that the sensitivity and sensitivity factors of force-sensitive structures are 0.15 KPa⁻¹ and 2.17 in the pressure range of 600–1000 KPa compressive stress and 20–50% tensile stress, respectively. These results are increased by 36.4% and 38.2% compared to the results of compressive stress (0.11 KPa⁻¹) and tensile stress (1.57) under DC conditions, respectively. It shows that the carbon nanotube/PDMS composite has higher test accuracy under AC conditions.