MANSOUR ALOTAIBI

Dr. MANSOUR ALOTAIBI


Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
8 July 2022 in Polymers
Verified
Journal Article
Open access
PDF file
TAThamer aldhafeeri
Thamer aldhafeeri
MAMANSOUR ALOTAIBI
MANSOUR ALOTAIBI
CBCarol Forance Barry
Carol Forance Barry
To reduce the degradation of polylactic acid (PLA) during processing, which reduces the molecular weight of PLA and its properties, prior studies have recommended low processing temperatures. In contrast, this work investigated the impact of four factors affecting shear heating (extruder type, screw configuration, screw speed, and feed rate) on the degradation of PLA. The polylactic acid was processed using a quad screw extruder (QSE) and a comparable twin screw extruder (TSE), two screw configurations, higher screw speeds, and several feed rates. The processed PLA was characterized by its rheological, thermal, and material composition properties. In both screw configurations, the QSE (which has a greater free volume) produced 3–4 °C increases in melt temperature when the screw speed was increased from 400 rpm to 1000 rpm, whereas the temperature rise was 24–25 °C in the TSE. PLA processed at low screw speeds, however, exhibited greater reductions in molecular weight—i.e., 9% in the QSE and 7% in the TSE. Screw configurations with fewer kneading blocks, and higher feed rates in the QSE, reduced degradation of PLA. At lower processing temperatures, it was found that an increase in melt temperature and shear rate did not significantly contribute to the degradation of PLA. Reducing the residence time during processing minimized the degradation of PLA in a molten state.

29 June 2022 in Polymers
Verified
Journal Article
Open access
PDF file
MAMANSOUR ALOTAIBI
MANSOUR ALOTAIBI
TAThamer aldhafeeri
Thamer aldhafeeri
CBCarol Forance Barry
Carol Forance Barry
During mechanical recycling, polypropylene typically is reprocessed using a single- or twin-screw extruder. The degradation of polypropylene during this reprocessing reduces the polymer’s molecular weight and, consequently, limits the performance of the recycled resin. This work investigated the impact of a quad screw extruder (QSE), which has greater free volume, on the reprocessing of an impact copolymer polypropylene. To mimic the recycling process, the polypropylene was subjected to three processing cycles using a QSE and a comparable twin-screw extruder (TSE) operated at three screw speeds. The reprocessed materials were characterized for their rheological, morphological, and mechanical properties. For both extruders, increasing the number of reprocessing cycles and the screw speed resulted in higher melt flow indices, decreases in zero-shear viscosity, and shifting of the crossover points for the storage and loss moduli, which indicate reductions in the molecular weight and narrowing of the molecular weight distribution of the polypropylene. The QSE exhibited greater reductions in molecular weight compared to the TSE, probably due to the higher stresses associated with the three intermeshing points along its screws. Reprocessing caused a significant reductions in the Izod impact strength of the reprocessed polypropylene, which correlated with reductions in the particle size and particle size distribution of the dispersed rubbery phase in the polypropylene during reprocessing.

28 April 2024 in Polymers
Verified
Journal Article
Open access
PDF file
SCSimran Chatrath
Simran Chatrath
MAMANSOUR ALOTAIBI
MANSOUR ALOTAIBI
CBCarol Forance Barry
Carol Forance Barry
Blends of polylactic acid (PLA) with amorphous polyhydroxyalkanoate (aPHA) are less brittle than neat PLA, thus enabling their use as biodegradable packaging. This work investigated the impact of recycling on the properties of neat PLA and PLA/aPHA blends with 90 and 75 wt. % PLA. After the materials were subjected to five heat histories in a single-screw extruder, the mechanical, rheological, and thermal properties were measured. All recycled compounds with 100% PLA and 75% PLA had similar decomposition behavior, whereas the decomposition temperatures for the blends with 90% PLA decreased with each additional heat cycle. The glass transition and melting temperatures were not impacted by reprocessing, but the crystallinity increased with more heat cycles. The complex viscosity of the reprocessed PLA and PLA/aPHA blends was much lower than for the neat PLA and increasing the number of heat cycles produced smaller reductions in the complex viscosity of 100% PLA and the blend with 90% PLA; no change in complex viscosity was observed for blends with 75% PLA exposed to 2 to 5 heat cycles. The tensile properties were not affected by reprocessing, whereas the impact strength for the 75% PLA blend decreased with reprocessing. These properties suggest that users will be able to incorporate scrap into the neat resin for thermoformed packaging.

4 June 2025 in Polymers
Verified
Journal Article
Open access
PDF file
MAMANSOUR ALOTAIBI
MANSOUR ALOTAIBI
JSJainam Shah
Jainam Shah
ASAniket Sadani
Aniket Sadani
CBCarol Forance Barry
Carol Forance Barry
Polylactic acid (PLA) has gained attention as a sustainable, compostable polyester, but process-induced degradation in single- and twin-screw extruders reduces PLA’s molecular weight and affects its properties. In addition, PLA is often blended with other materials to improve its properties. A continuous mixer, which provides tighter control of shear levels and lower processing temperatures, produces less degradation of heat-sensitive polymers like polyvinyl chloride, but there is limited information about the effects of machine design and processing parameters. Therefore, this work investigated three parameters in the mixer section (rotor design, rotor speed, and orifice position) and screw speeds in the extruder section when processing PLA using a continuous mixer. The resultant PLA samples were characterized for their rheological, thermal, and chemical structure properties. It was found that higher rotor speeds and smaller orifice openings resulted in lower molecular weights, whereas varying the screw speed in the extruder did not significantly affect the molecular weight. Rotor design substantially impacted degradation, with rotors that provided lower shear stress and residence time producing very low reductions in molecular weight. Overall, this work provided insight on how to select rotors and processing parameters to reduce degradation of PLA for continuous mixer

25 February 2025 in Polymers
Verified
Journal Article
Open access
PDF file
MAMANSOUR ALOTAIBI
MANSOUR ALOTAIBI
CBCarol Forance Barry
Carol Forance Barry
Continuous mixers, which consist of a section with non-intermeshing counter-rotating rotors and a single-screw extruder, were developed for thermoset rubber and are often used for compounding of heavily filled thermoplastics. Due to the high mixing efficiency and tight control of shear levels, they may be suited for other compounding other material systems. Little work, however, has been reported on compounding with these mixers, and preliminary work with polypropylene showed interesting limitations of the mixing parameters. Therefore, this study investigated the effects of nine rotor designs, two single-screw designs, rotor speed, feed rate, and orifice setting on the residence time and melt temperature in a Farrel Compact Processor. In general, single-stage rotors produced lower mixer residence times and melt temperatures compared to longer two-stage and high dispersion rotors. Higher rotor speeds and feed rates and smaller orifice openings generally reduced mixer residence times. Higher rotor speeds increased mixer melt temperatures, whereas higher feed rates and smaller orifice openings produced lower mixer melt temperatures. The single-screw design impacted the residence time but not the melt temperature. Overall, the results of this work provided strategies for optimizing the processing parameters and rotor design selection when melt compounding with continuous mixers.