This study investigates the impact of different water coupling coefficients on the blasting effect of red sandstone. The analysis is based on the theories of detonation wave and elastic wave, focusing on the variation in wall pressure of the blasting holes. Using DDNP explosive as the explosive load, blasting tests were conducted on red sandstone specimens with four different water coupling coefficients: 1.20, 1.33, 1.50, and 2.00. The study examines the morphologies of the rock specimens after blasting under these different water coupling coefficients. Additionally, the fractal dimensions of the surface cracks resulting from the blasting were calculated to provide a quantitative evaluation of the extent of rock damage. CT scanning and 3D reconstruction were performed on the post-blasting specimens to visually depict the extent of damage and fractures within the rock. Additionally, the volume fractal dimension and damage degree of the post-blasting specimens are calculated. The findings are then combined with numerical simulation to facilitate auxiliary analysis. The results demonstrate that an increase in the water coupling coefficient leads to a reduction in the peak pressure on the hole wall and the crushing zone, enabling more of the explosion energy to be utilized for crack propagation following the explosion. The specimens exhibited distinct failure patterns, resulting in corresponding changes in fractal dimensions. The simulated pore wall pressure–time curve validated the derived theoretical results, whereas the stress cloud map and explosion energy-time curve demonstrated the buffering effect of the water medium. As the water coupling coefficient increases, the buffering effect of the water medium becomes increasingly prominent.
27 November 2017 in Fatigue & Fracture of Engineering Materials & Structures
The effects of low temperature gradient on dynamic mechanical properties of coal were examined through Split-Hopkinson Pressure Bar (SHPB) Dynamic Impact Experiment, the law of dynamic mechanical parameters of coal specimen changing from room temperature to negative temperature (25 °C, −5 °C, −10 °C, −15 °C, −20 °C, −30 °C, −40 °C) was analyzed, and the coal-rock stress-strain curve characteristics subject to the low temperature-impact load coupling effect was discussed. The law of the effects of different strain rates on the rock strength properties and the compressive deformation and failure was analyzed by studying the coal specimen at −15 °C. Moreover, the mechanical properties of coal specimen in saturated and dry conditions were compared, and the effects of water and water-ice phase transition on the strength properties of the corresponding coal specimen were analyzed.
In 2012, the International Society for Rock Mechanics (ISRM) recommended a new Notched Semicircular Bend (NSCB) method for the determination of dynamic fracture toughness of rock materials, but it did not consider the effect of some uncontrollable factors in the course of the experiment on the test result. This thesis firstly carried out dynamic fracture toughness experiments on several typical rock materials such as sandstone using the modified Split‐Hopkinson Pressure Bar (SHPB) experimental system with high‐speed photography, directly compared the dynamic fracture failure characteristics of several rock materials, and examined the loading rate dependency of the dynamic fracture toughness of rock materials. Based on the numerical analysis method of Discrete Lattice Spring Model (DLSM), it focused on the effect of bullet impact loading rate, loading area of incident bar, support restraints of clamping specimen, and other uncontrollable factors in the course of SHPB experiment on test results. The findings can be referenced for the improvement of NSCB method.
The testing system of digital laser dynamic caustics was performed here to examine the super-dynamic fracture mechanics of directional blasting crack, which, using an irregular shape cartridge, revealed the rock breaking mechanism of directional fracture blast. The findings show that the blasting primary crack fracture features—the typical tensile break, the variation trend of the dynamic stress intensity factor (DSIF), crack propagation velocity, and crack length— were more or less the same, the primary crack fracture was finished during 60–200 μs, the limit DSIF scarcely exceeded 1.5 MN/m3/2, and the arrest toughness of the blasting fracture was about 0.3 MN/m3/2. The irregular shape cartridge showed significant detonation wave unloading effects and detonation gas jet effects in the accumulative direction or slotting direction; the “air wedge effect” of the high-pressure detonation gas jet acted as the main drive for further expansion of the compression radial crack in the accumulative direction (or slotting direction), which also held the propagation of the compression radial crack in the nonaccumulative or nonslotting direction). Additionally, the accumulative cartridge and slotted cartridge were applied to the construction field, and it was found that the directional fracture blast was enabled, the good blasting fracture surface was formed, and better economic benefits and less operation time could be achieved using these two cartridges.
In order to examine the dynamic mechanical properties, dynamic crack proposition process, and energy loss of fractured rock under dynamic loading, the specimens with different fracture dig angles were processed with Φ50 mm × 50 mm cylindrical sandstone, the impact loading test was conducted on 50 mm stem diameter split Hopkinson pressure bar (SHPB) experiment platform, and the whole process of crack propagation and dynamic failure was recorded using a high-speed camera. As a result, the dynamic mechanical properties such as stress wave fluctuation characteristics, peak strength and stress-strain relationship, crack initiation angle, stress and other dependencies with prefabricated fracture angle of the prefabricated fracture specimens under high strain rate were obtained, and the incident energy, absorbed energy, and energy absorption rates were compared to investigate the energy loss law in the dynamic loading; on the contrary, the effects of different loading rates on the dynamic mechanical properties of the sandstone specimens were identified, and finally a set of findings were presented.