This study investigates a post treatment method for improving the thermoelectric properties of carbon nanotube (CNT)/poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) nanocomposite films. Ethylene glycol (EG) treatment is performed by immersing the as-prepared CNT/PEDOT:PSS nanocomposite films in EG for 1 h followed by annealing at 140 °C for 10 min. Non-complexed PSS chains could be effectively removed using the EG treatment, resulting in a decrease in inter-bundle distances in the nanocomposite films. This drastically increases the electrical conductivity of the PEDOT:PSS matrix. EG-treated nanocomposite films with 20 wt% CNTs exhibited the highest power factor of 151 ± 34 μW m−1 K−2 among all the prepared samples. Our results indicate that the EG treatment is a promising method for fabricating cost-effective, high-performance thermoelectric CNT/PEDOT:PSS nanocomposite films. We fabricated an organic thermoelectric generator using EG-treated CNT/PEDOT:PSS nanocomposite patterns and evaluated its electric power generation capabilities.
We studied the thermoelectric properties of a diketopyrrolopyrrole-based semiconductor (PDPP3T) via a precisely tuned doping process using Iron (III) chloride. In particular, the doping states of PDPP3T film were linearly controlled depending on the dopant concentration. The outstanding Seebeck coefficient of PDPP3T assisted the excellent power factors (PFs) over 200 μW m−1K−2 at the broad range of doping concentration (3–8 mM) and the maximum PF reached up to 276 μW m−1K−2, which is much higher than that of poly(3-hexylthiophene), 56 μW m−1K−2. The high-mobility of PDPP3T was beneficial to enhance the electrical conductivity and the low level of total dopant volume was important to maintain high Seebeck coefficients. In addition, the low bandgap PDPP3T polymer effiectively shifted its absorption into near infra-red area and became more colorless after doping, which is great advantage to realize transparent electronic devices. Our results give importance guidance to develop thermoelectric semiconducting polymers and we suggest that the use of low bandgap and high-mobility polymers, and the accurate control of the doping levels are key factors for obtaining the high thermoelectric PF.
This study demonstrates a simple two-step post-treatment method for improving the thermoelectric power factor of low-cost poly(3,4-ethylenedioxythiophene):poly(4-styrenesulfonate) (PEDOT:PSS) films. The dry re-dispersible PEDOT:PSS pellets are cost-effective, however, they exhibit extremely low thermoelectric performance. On treating with ethylene glycol followed by hydrazine, the power factor of the PEDOT:PSS films increased from 0.0632±0.0097 μW m −1 K −2 to 13.3±1.5 μW m −1 K −2 . The enhancement might be attributed to the effective removal of the free, non-complexed PSS chains and fine control of the oxidation level of PEDOT by the two-step post-treatment.
25 May 2017 in Physical Chemistry Chemical Physics
We developed a facile method for treating polyimide-based organic gate insulator (OGI) surfaces with self-assembled monolayers (SAMs) by introducing metal-oxide interlayers, called the metal-oxide assisted SAM treatment (MAST). To create sites for surface modification with SAM materials on polyimide-based OGI (KPI) surfaces, the metal-oxide interlayer, here amorphous alumina (α-Al2O3), was deposited on the KPI gate insulator using spin-coating via a rapid sol–gel reaction, providing an excellent template for the formation of a high-quality SAM with phosphonic acid anchor groups. The SAM of octadecylphosphonic acid (ODPA) was successfully treated by spin-coating onto the α-Al2O3-deposited KPI film. After the surface treatment by ODPA/α-Al2O3, the surface energy of the KPI thin film was remarkably decreased and the molecular compatibility of the film with an organic semiconductor (OSC), 2-decyl-7-phenyl-[1]benzothieno[3,2-b][1]benzothiophene (Ph-BTBT-C10), was increased. Ph-BTBT-C10 molecules were uniformly deposited on the treated gate insulator surface and grown with high crystallinity, as confirmed by atomic force microscopy (AFM) and X-ray diffraction (XRD) analysis. The mobility of Ph-BTBT-C10 thin-film transistors (TFTs) was approximately doubled, from 0.56 ± 0.05 cm2 V−1 s−1 to 1.26 ± 0.06 cm2 V−1 s−1, after the surface treatment. The surface treatment of α-Al2O3 and ODPA significantly decreased the threshold voltage from −21.2 V to −8.3 V by reducing the trap sites in the OGI and improving the interfacial properties with the OSC. We suggest that the MAST method for OGIs can be applied to various OGI materials lacking reactive sites using SAMs. It may provide a new platform for the surface treatment of OGIs, similar to that of conventional SiO2 gate insulators.
24 February 2016 in Physical Chemistry Chemical Physics
This study investigates a spin-coating method for modifying the surface properties of a poly(ethylene-alt-maleic anhydride) (PEMA) gate insulator. The 60 nm-thick PEMA thin film exhibits excellent electrical insulating properties, and its surface properties could be easily modified by surface grafting of octylamine. Due to surface treatment via spin-coating, the surface energy of the PEMA gate insulator decreased, the crystal quality of the organic semiconductor improved, and consequently the performance of low-voltage organic thin-film transistors (TFTs) was enhanced. Our results suggest that the surface treatment of the PEMA gate insulator could be a simple and effective method for enhancing the performance of organic TFTs.
Ultrasmall polymersomes of poly-α,β-(N-2-hydroxyethyl L-aspartamide)-graft-poly(L-lactic acid), 40–45 nm in diameter, were prepared based on a well-defined graft copolymer architecture and well-managed self-assembly process. The ultrasmall polymersomes are a proposed drug delivery platform based on their suitable size, narrow size distribution, uniform morphology, and high thermodynamic stability, which satisfy prerequisites for systemic drug delivery carriers. The functionality and versatility of this system as a potential general drug delivery platform are supported by its biodegradability, favorable modifiable chemical formula, and flexible polymersome size that could be tuned to a nanoscopic range by manipulating the thermodynamic balance of the self-assembly process.