This paper discusses the design and implementation of a portable IoT station. Communication and data synchronization issues in several installations are addressed here, making possible a detailed analysis of the entire system during its operation. The system operator requires a synchronized data stream, combining multiple communication protocols into one single time stamp. The hardware selected for the portable IoT station complies with the International Electrotechnical Commission (IEC) industrial standards. A short discussion regarding interface customization shows how easily the hardware can be modified so that it is integrated with almost any system. A programmable logic controller enables the Node-RED to be utilized. This open-source middleware defines operations for each global variable nominated in the Modbus register. Two applications are presented and discussed in this paper; each application has a distinct methodology utilized to publish and visualize the acquired data. The portable IoT station is highly customizable, consisting of a modular structure and providing the best platform for future research and development of dedicated algorithms. This paper also demonstrates how the portable IoT station can be implemented in systems where time-based data synchronization is essential while introducing a seamless implementation and operation.

This paper proposes a design for a platform-based Multi-phase Interleaved Synchronous Buck Converter (MISBC). A custom platform was developed to compare the theoretical performance of a MISBC circuit simulated with Multisim to a prototype that was built at Western Sydney University. The work disclosed in this manuscript describes some steps adopted during the selection of each component and technical considerations taken during the design of the Printed Circuit Board (PCB). The platform designed has a maximum power output of 260 Watts, with a buck reduction of the nominal voltage from 97 Volts to 24 Volts at a maximum switching frequency of 50 kHz. This switching frequency is achieved with an open-loop circuit configuration coupled with synchronized signal generators, used to validate the dead band required between the activation of each set of transistors implemented in a half-bridge configuration. A summary of the results based on the duty cycle required to achieve the buck voltage desired highlights the advantages of each operating mode of the MISBC circuit. Here the theoretical performance is compared against the data acquired during functional evaluations of the prototype, making possible future interpretations of the ideal control algorithm required to maximize the performance output of MISBC circuits.

This paper proposes a design for a platform-based Multi-phase Interleaved Synchronous Buck Converter (MISBC) using Silicon (Si) based Metal-Oxide-Semiconductor Field-Effect Transistors (MOSFETs). A custom platform was developed to compare the theoretical performance of a MISBC circuit simulated with Multisim and compared it with a prototype that was built at Western Sydney University. The work disclosed in this manuscript describes some steps adopted during the selection of each component and technical considerations taken during the design of the Printed Circuit Board (PCB). The platform designed has a maximum power output of 260 Watts, with a buck reduction of the nominal voltage from 97 Volts to 24 Volts at a maximum switching frequency of 50 kHz. This switching frequency is achieved with an open-loop circuit configuration coupled with synchronized signal generators, used to validate the dead band required between the activation of each MOSFET implemented in a half bridge configuration. A summary of the results based on the duty cycle required to achieve the buck voltage desired highlights the advantages of each operating mode of the MISBC circuit, where the theoretical performance is compared against the data acquired during functional evaluations of the prototype, allowing further interpretations towards the optimal control algorithm required to maximize the performance output of MISBC circuits.

This paper discusses the design and implementation of a portable IoT station. Communication and data synchronization issues in several installations are addressed here, making possible a detailed analysis of the entire system during its operation. The system proposed is interpreted as an additional tool which can be utilized in several applications, where the system operator requires a synchronized data stream, combining multiple communication protocols into one single time stamp. The hardware selected for the portable IoT station complies with the International Electrotechnical Commission (IEC) industrial standards. A short discussion regarding interface customization shows how easily the hardware can be modified so that it is integrated with almost any system. A Programmable Logic Controller enables the Node-Red to be utilized. This open-source programming tool employs flows to define operations for each global variable nominated in the Modbus register. Two applications are presented and discussed in this paper, each application has a distinct methodology utilized to publish and visualize the acquired data. The portable IoT Station is highly customizable, consisting of a modular structure and providing the best platform for future research and development of dedicated algorithms.