Halloysite is a unique 1:1 clay mineral frequently appearing with nanotubular morphology, and having surfaces of different polarity with interesting and important technological applications. HNTs can be consolidated naturally in the earth by pressure and thermal flows. In this study of natural consolidated HNTs, the strength and hardness of these materials were found to be dependent on the presence of impurities (gibbsite, alunite, quartz, and other silica minerals), which accounted for the increased stability of such samples. In the absence of impurities, the strength of consolidated HNTs was significantly lower. The first 3D mapping of the pore structure of natural consolidated HNT is provided. The contributions of the porosity within the nanotubes and between the nanotubes were delineated using a combination of non-invasive ultra-small and small-angle X-ray scattering (USAXS/SAXS) analyses, BET/BJH pore size analyses, and computed tomography studies. A total porosity of 40%, as determined by X-ray attenuation and He porosimetry, was found for the natural consolidated HNTs, of which about one-third was due to the inter-HNT porosity. Nano-X-ray computed tomography (nano-XCT) analyses also indicated that 76% of the inter-HNT pores were smaller than 150 nm in diameter. The intra-HNT pore size determined by combined USAXS/SAXS and BET/BJH was about 10 nm. This pore network information is essential for the utilization of natural consolidated HNTs as a model geomaterial to investigate the effects of surface characteristics on confined fluid flow.

Most reported slip length measurements have been made at the surfaces of synthetic materials and modified synthetic materials. In contrast, few slip length measurements at the surface of unmodified natural mineral surfaces have been reported. In this regard, flow at the silica face surfaces of the phyllosilicate minerals, talc and mica, was considered. A slip boundary condition was expected at the nonpolar hydrophobic silica surface of talc leading to enhanced flow, and a no-slip boundary condition was expected at the hydrophilic silica surface of mica. Atomic force microscopy (AFM) slip length measurements were made at the talc and mica surfaces. The slip length results for the hydrophobic silica surface of talc were contrasted to the results for the hydrophilic silica surface of mica (no-slip flow). The results are discussed based on molecular dynamics simulations (MDS), as reported in the literature, and AFM images of surface nanobubbles. For nonpolar hydrophobic surfaces (such as talc), it is doubtful that the MDS interfacial water structure and the water exclusion zone (3.2 Å) account for the AFM slip flow with slip lengths as great as 95 nm. Rather, a better explanation for the AFM slip flow condition is based on reduced interfacial viscosity due to the presence of dissolved gas and the accommodation of pancake nanobubbles at the talc surface having a height dimension of magnitude similar to the slip length.

Graphene-based Nano-sensor has the characteristics of short response time, high conductivity and recoverability. In this work, graphene coated glass fiber sensor and graphene film sensor were fabricated by pressing and oxidation-reduction method, respectively. Graphene coated glass fiber sensor was used to test the pressure of blood pressure and weight. Graphene film sensor was used to test the bending of human fingers, elbows and knees. The results show that the conductivity of the graphene coated glass fiber sensor is 23260S/m, and that of the graphene film sensor is 20000S/m. Both graphene-based sensors have good linear relationship with external load and deformation, and can be used for real-time monitoring of human behavior.

Surface wettability is determined by the attraction of a liquid phase to a solid surface. It is typically quantified by using contact angle measurements at mineral surfaces in the case of the flotation of mineral particles. Contact angle research to describe wettability has been investigated at different scales by sessile drop measurements, molecular dynamic simulation, and atomic force microscopy. In this study, the density functional theory (DFT) was employed for predicting the surface free energy and contact angles of a well-known hydrophobic phyllosilicate mineral talc and a well-known hydrophilic phyllosilicate mineral muscovite based on the calculated interfacial energy and surface charge. The results revealed that the predicted contact angle at the atomic scale was larger than the experimental value, and identified two interactions: electrostatic interaction and hydrogen bonding, between the hydrophilic muscovite surface and the water layer, while a water-exclusion zone of 3.346 Å was found between the hydrophobic talc surface and the first water layer. This investigation gives a new perspective for wettability determination at the atomic scale.