Insect-sized ( $\sim$ 100 mg) aerial robots have advantages over larger robots because of their small size, low weight, and low materials cost. Previous iterations have demonstrated controlled flight but were difficult to fabricate because they consisted of many separate parts assembled together and were also unable to perform locomotion modes besides flight. This article presents a new design of a 74-mg flapping-wing robot that dramatically reduces the number of parts and simplifies fabrication. The robot also has a lower center of mass, which allows the robot to additionally land without the need for long legs, even in case of unstable flight. We also show that the new design allows for wing-driven ground and air–water interfacial locomotion, improving the versatility of the robot. During surface ambulation, forward thrust is generated by increasing the speed of the upstroke relative to the downstroke of the flapping wings. Adjusting relative wing stroke amplitudes also allows for steering. The ability to land and subsequently move along the ground first presented here allows the robot to negotiate extremely confined spaces and underneath obstacles. We present results demonstrating these capabilities, as well as hovering flight and controlled landing.
17 January 2020 in IEEE Robotics and Automation Letters
Successful demonstrations of controlled flight in flying insect-sized robots (FIRs) $< 500 \text{mg}$ have all relied on piezo-actuated flapping wings because of unfavorable downward size scaling in motor-driven propellers. In practice, the mechanical complexity of flapping wings typically results in large torque bias variability about pitch and roll axes, leading to rapid rotation in free flight for vehicles that are not properly trimmed. Manual trimming by watching high-speed video is tedious and error-prone. In this letter, we introduce an alternative, a trimming device that uses feedback from motion capture cameras to determine and correct for bias torques. It does so using an automated feedback loop, without the need for any visual feedback from the user, or airborne flights which can damage the robot. We validated the device on two different robot flies. After trimming with our device, the robots both took off approximately vertically in open-loop and were able to hover in free flight under feedback control. Our system, therefore, speeds up an essential yet time-consuming step in robot fly fabrication, facilitating their eventual mass production and practical application.
To date, insect scale robots capable of controlled flight have used flapping-wings for generating lift, but this requires a complex and failure-prone mechanism. A simpler alternative is electrohydrodynamic (EHD) thrust, which requires no moving mechanical parts. In EHD, corona discharge generates a flow of ions in an electric field between two electrodes; the high-velocity ions transfer their kinetic energy to neutral air molecules through collisions, accelerating the gas and creating thrust. We introduce a fabrication process for EHD thruster based on 355 nm laser micromachining, which potentially allows for greater materials selection, such as fiber-based composites, than is possible with semiconductor-based lithographic processing. Our four-thruster device measures 1.8 × 2.5 cm and is composed of steel emitters and a lightweight carbon fiber mesh. We measured the electrical current and thrust of each thruster of our four-thruster design, showing agreement with the Townsend relation. The peak thrust of our device, at 5.2 kV, was measured to be 3.03 times its 37 mg (363.0 μN) mass using a precision balance. In free flight, we demonstrated liftoff at 4.6 kV.
19 February 2021 in IEEE Robotics and Automation Letters
Flapping-wing insect-scale robots (<;$500 mg) rely on small changes in drive signals supplied to actuators to generate angular torques. Previous results on vehicles with passive wing hinges have demonstrated roll, pitch, and position control, but they have not yet been able to control their yaw (heading) angle while hovering. To actuate yaw, the speed of the downstroke can be changed relative to the upstroke by adding a second harmonic signal at double the fundamental flapping frequency. Previous work has shown that pitching dynamics of a passive spring-like wing hinge reduces the aerodynamic drag available to produce yaw torque. We introduce three innovations that increase yaw actuation torque: 1) a new two-actuator robot fly design that increases the moment arm, 2) wider actuators that increase the operating frequency, and 3) a phase shift to the second harmonic signal. We validated these results through simulation and experiment. Further, we present the first demonstration of yaw angle control on a passive-hinge vehicle in a controlled flight. Our new robot fly design, UW Robofly-Expanded, weighs 160 mg (two toothpicks) and requires only two piezo actuators to steer itself.
The three-point hitch, found on agricultural tractors, facilitates the raising and lowering of an attached implement. Some tractors include a rock shaft that comprises a physical shaft that interconnects and facilitates the raising and lowering of the lower arms of the three-point hitch in a synchronized manner. In this study, we deal with a hitch system with the lower arms actuated by two independent hydraulic cylinders. This innovative tractor hitch system design allows the implement to follow the terrain, instead of the tractor, about the fore–aft (roll) axis of the tractor. However, since the two lower arms are independent, a specialized controller is needed to move these arms in unison. First, we present a position controller for individual arms and a roll controller to move these arms together. Second, we present a unique algorithm to emulate a physical rock shaft while the implement is operating in float mode. The algorithm ensures that the implement does not roll around the fore–aft axis while making sure it moves up and down vertically to follow the terrain. We present experimental results from the step response of the hitch system’s height while tracking a velocity reference. With the roll of the implement defined as the difference between the left arm’s position in percentage and that of the right arm in percentage, we observe that the largest mean roll was 0.23% with a flail mower attached and 0.26% without any implement. We then present results from the implement’s position in the float mode when the software rock shaft was activated and compare them with the case without the software rock shaft. The experiments showed that, when the software rock shaft was turned on, the mean roll reduced from 4.64% to 0.58% with a seed drill implement and from −3.99% to −0.59% with a flail mower implement. The standard deviations in these two implement cases improved from 16.77% to 2.79% and 6.45% to 3.53%, respectively, proving the effectiveness of the software rock shaft and its potential to replace the physical rock shaft found on the traditional tractors.
Aerial robots the size of a honeybee (~100 mg) have advantages over larger robots because of their small size, low mass and low materials cost. Previous iterations have demonstrated controlled flight but were difficult to fabricate because they consisted of many separate parts assembled together. They also were unable to perform locomotion modes besides flight. This paper presents a new design of a 74 mg flapping-wing robot that dramatically reduces the number of parts and simplifies fabrication. It also has a lower center of mass, which allows the robot to additionally land without the need for long legs, even in case of unstable flight. Furthermore, we show that the new design allows for wing-driven ground and air-water interfacial locomotion, improving the versatility of the robot. Forward thrust is generated by increasing the speed of downstroke relative to the upstroke of the flapping wings. This also allows for steering. The ability to land and subsequently move along the ground allows the robot to negotiate extremely confined spaces, underneath obstacles, and to precise locations. We describe the new design in detail and present results demonstrating these capabilities, as well as hovering flight and controlled landing.