A series of novel 3,9-disubstituted acridines were synthesized and their biological potential was investigated. The synthetic plan consists of eight reaction steps, which produce the final products, derivatives 17a–17j, in a moderate yield. The principles of cheminformatics and computational chemistry were applied in order to study the relationship between the physicochemical properties of the 3,9-disubstituted acridines and their biological activity at a cellular and molecular level. The selected 3,9-disubstituted acridine derivatives were studied in the presence of DNA using spectroscopic (UV-Vis, circular dichroism, and thermal denaturation) and electrophoretic (nuclease activity, relaxation and unwinding assays for topoisomerase I and decatenation assay for topoisomerase IIα) methods. Binding constants (2.81–9.03 × 10⁴ M⁻¹) were calculated for the derivatives from the results of the absorption titration spectra. The derivatives were found to have caused the inhibition of both topoisomerase I and topoisomerase IIα. Molecular docking simulations suggested a different way in which the acridines 17a–17j can interact with topoisomerase I versus topoisomerase IIα. A strong correlation between the lipophilicity of the derivatives and their ability to stabilize the intercalation complex was identified for all of the studied agents. Acridines 17a–17j were also subjected to in vitro screening conducted by the Developmental Therapeutic Program of the National Cancer Institute (NCI) against a panel of 60 cancer cell lines. The strongest biological activity was displayed by aniline acridine 17a (MCF7–GI₅₀ 18.6 nM) and N,N-dimethylaniline acridine 17b (SR–GI₅₀ 38.0 nM). The relationship between the cytostatic activity of the most active substances (derivatives 17a, 17b, and 17e–17h) and their values of K_B, LogP, ΔS°, and δ was also investigated. Due to the fact that a significant correlation was only found in the case of charge density, δ, it is possible to assume that the cytostatic effect might be dependent upon the structural specificity of the acridine derivatives.

This study presents the design, preparation, and characterization of thirty new medium-entropy alloys (MEAs) in three systems: Al-Ti-Nb-Zr, Al-Ti-Nb-V, and Al-Ti-Nb-Hf. The hardness of the alloys ranged from 320 to 800 HV_0.3. Among the alloys studied, Al₁₅Ti₄₀Nb₃₀Zr₁₅ exhibited the highest-reversible hydrogen storage capacity (1.03 wt.%), with an H/M value of 0.68, comparable to LaNi₅, but with a reduced density (5.11 g·cm⁻³) and without rare earth elements. This study further reveals a strong correlation between hardness and hydrogen absorption/desorption; higher hardness is responsible for reduced hydrogen uptake. This finding highlights the interplay between a material’s properties and hydrogen storage behavior in MEAs, and has implications for the development of efficient hydrogen storage materials.

The Mg-Zn-Ca system has previously been proposed as the most suitable biodegradable candidate for biomedical applications. In this work, a series of ribbon specimens was fabricated using a melt-spinning technique to explore the glass-forming ability of the Mg-Zn-Ca system along the concentration line of 7 at.% of calcium. A glassy state is confirmed for Mg₅₀Zn₄₃Ca₇, Mg₆₀Zn₃₃Ca₇, and Mg₇₀Zn₂₃Ca₇. Those samples were characterised by standard methods to determine their mass density, hardness, elastic modulus, and crystallisation temperatures during devitrification. Their amorphous structure is described by means of pair distribution functions obtained by high-energy X-ray and neutron diffraction (HEXRD and ND) measurements performed at large-scale facilities. The contributions of pairs Mg-Mg, Mg-Zn, and Zn-Zn were identified. In addition, a transformation process from an amorphous to crystalline structure is followed in situ by HEXRD for Mg₆₀Zn₃₃Ca₇ and Mg₅₀Zn₄₃Ca₇. Intermetallic compounds IM1 and IM3 and hcp-Mg phase are proposed to be formed in multiple crystallisation eventss.

Hydrogen is a key element in the changing energy sector and presents an accessible alternative to conventional fossil fuel sources. In this work, a system of ten high-entropy alloys was prepared based on the Hume-Rothery rules. One of the biggest advantages of these alloys is their storage capacity, which reaches the highest value among all known alloys intended for hydrogen storage. Alloys based on Al-Ti-Nb-Zr elements with different atomic fractions show interesting accumulation capabilities with fast absorption kinetics and low specific gravity. Each alloy in this study underwent high-pressure gravimetric absorption and desorption tests. The main goals of this work were to prepare alloys with the lowest-possible specific gravity and the highest-possible storage capacity. One alloy from our system shows storage capacity values similar to commercial alloys, without any rare-earth elements.

TiVNbZrCr high-entropy intermetallic alloy was investigated as a deuterium storage material using gravimetric sorption measurements, thermogravimetric analysis, and temperature-resolved synchrotron X-ray diffraction during deuterium desorption. The as-prepared alloy had an experimentally determined composition of Ti₁₇V₁₉Zr₁₉Nb₂₂Cr₂₃ and a density of 6.59 g·cm⁻³. Empirical alloy-design parameters indicate that the alloy is not a single-phase bcc solid solution, but rather a compositionally complex intermetallic alloy. The calculated hydrogen-affinity descriptors suggest a strong thermodynamic driving force for deuteride formation. Under 5 MPa D₂, the alloy absorbed 3.28 wt.% D, corresponding to D/M = 1.1. After ex situ deuteration, additional diffraction reflections were indexed using tetragonal deuteride reference structures corresponding to ZrV₂D_2.35 and TiD₂, while the Cr-rich bcc phase remained comparatively stable. Thermal desorption released 2.28 wt.% D up to 600 °C in three partially overlapping steps. These results demonstrate that deuterium storage in TiVNbZrCr is governed by phase-selective deuteride formation and decomposition rather than by homogeneous bcc lattice expansion.