Manuel Christian Johann Schachinger

Mr. Manuel Christian Johann Schachinger

orcid

Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
17 May 2024 in Materials
Verified
Journal Article
Open access
PDF file
CLChristof Lanzerstorfer
Christof Lanzerstorfer
CFChristian Forsich
Christian Forsich
FDFrancisco Delfin
Francisco Delfin
MSManuel Christian Johann Schachinger
Manuel Christian Johann Schachinger
DHDaniel Heim
Daniel Heim
The wall friction angle is an important parameter in powder flow. In a recent study for various powders, a reduction in the wall friction angle for steel was demonstrated by the application of an a-C:H:Si film on the steel surface. This work presents the results of a study of this effect in more detail regarding the influence of the powder material, the wall normal stress and the particle size of the powder for mass median diameters from 4 µm to approximately 150 µm. The wall friction angles were measured using a Schulze ring shear tester for three different powder materials: aluminum oxide, calcium carbonate and silicon carbide. The results showed little difference with respect to powder chemistry. For the coarser powders, the reduction in the wall friction angle due to the a-C:H:Si coating was highest (10° to 12°) and rather stress-independent, while for the fine and medium-size powders the reduction was lower and stress-dependent. With increasing wall normal stress, the reduction in the wall friction angle increased. These results can be explained by the friction reduction mechanism of a-C:H:Si, which requires a certain contact pressure for superficial graphitization.

9 September 2026 in SSRN Electronic Journal
Verified
Preprint
Open access
Florian KlapalFlorian Klapal
Florian Klapal
SFStefanie Flatscher
Stefanie Flatscher
JDJonáš Dařílek
Jonáš Dařílek
MWMarkus Wierer
Markus Wierer
MSManuel Christian Johann Schachinger
Manuel Christian Johann Schachinger
Mark HlawitschkaMark Hlawitschka
Mark Hlawitschka
Lithium carbonate is an important commercial lithium product and precursor for batterygrade materials. Replacing conventional Na2CO3-based precipitation with CO2-based carbonate generation may couple lithium recovery with CO2 utilisation, but the effects of carbonate supply pathway and hydrodynamic control on recoverypurity tradeoffs remain insufficiently clarified. In this study, solid-liquid, liquid-liquid/slurry, and gas-liquid precipitation routes were compared at laboratoryscale using solutions with a concentration of 20 g L-1 Li. Hydrodynamic control was then investigated in a technicalscale column by varying sparger pore size between 1.0, 1.5 and 2.5 mm. At laboratoryscale, the liquid-liquid/slurry route achieved 74% Li2CO3-based lithium recovery, but the lowest purity of 79% Li2CO3. The solidliquid route provided a better recovery-purity balance, with 70% recovery and 87% purity. Gasliquid precipitation at 5 M NaOH was limited by the hydroxide inventory required for the carbonate formation, giving recovery rates of 22-25%, whereas 20 M NaOH shifted speciation towards CO32- and raised recovery to 80% at 87% purity. At technicalscale, the 1.0 and 1.5 mm spargers gave comparable CO2 uptake of 182 and 179 L, while the 2.5 mm sparger reduced CO2 uptake to 99 L. The 1.5 mm sparger provided the most favourable compromise, achieving 61% recovery and 88% purity. Overall, carbonate supply pathway, alkalinity and sparger design jointly determine the recoverypurity balance in scalable CO2 based Li2CO3 precipitation.