A novel method is proposed for accurately determining the local wall friction through the near-wall measurement of time-average velocity profile in a Type-A turbulent boundary layer (TBL). The method is based on the newly established analytical wall-law in Type-A TBL. The direct numerical simulations (DNS) data of turbulence on a zero-pressure-gradient flat-plate (ZPGFP) is used to demonstrate the accuracy and the robustness of the approach. To verify the reliability and applicability of the method, a two-dimensional particle image velocimetry (PIV) measurement was performed in a ZPGFP TBL with a low-to-moderate Reynolds number (Re). Via utilizing the algorithm of single-pixel ensemble correlation (SPEC), the velocity profiles in the ZPGFP TBL were resolved at a significantly improved spatial resolution, which greatly enhanced the measurement accuracy and permitted us to accurately capture the near-wall velocity information. The accuracy of the approach is then quantitatively validated for the high Reynolds number turbulence using the ZPGFP TBL data. The research demonstrates that the current method can provide the precise estimation of wall friction with a mean error of less than 2%, which not only possesses the advantage of its insensitivity to the absolute wall-normal distance of the measuring point, but also its capability of providing an accurate prediction of wall shear stress based on fairly sparse experimental data on the velocity profile. The current study demonstrates that the wall shear stress can be accurately estimated by a velocity even at a single-point either measured or calculated in the near-wall region.

This study employs Direct Numerical Simulation (DNS) to investigate the flow and heat transfer characteristics in a compressor blade passage at five Reynolds numbers ($Re=1.091\times {10}^5$, $1.229\times {10}^5$, $1.367\times {10}^5$, $1.506\times {10}^5$, and $1.645\times {10}^5$). A recent method based on local inviscid velocity reconstruction is applied to define and calculate boundary layer parameters, whereas the Rortex vortex identification method is used to analyze turbulent vortical structures. Results indicate that $Re$ significantly affects separation bubble size, transition location, and reattachment behavior, thereby altering wall heat transfer characteristics. On the pressure surface, separation and early transition are observed at higher $Re$, with the Nusselt number ($Nu$) remaining high after transition. On the suction surfaces, separation occurs such that large-scale separation at low $Re$ reduces $Nu$, while reattachment combined with turbulent mixing at high $Re$ significantly increases $Nu$. Turbulent vortical structures enhance near-wall fluid mixing through induced ejection and sweep events, thereby promoting momentum and heat transport. As $Re$ increases, the vortical structures become denser with reduced scales and the peaks in heat flux move closer to the wall, thus improving convective heat transfer efficiency.

A novel method is proposed for accurately determining the local wall friction through the near-wall measurement of time-average velocity profile in a Type-A turbulent boundary layer (TBL). The method is based on the newly established analytical wall-law in Type-A TBL. The direct numerical simulations (DNS) data of turbulence on a zero-pressure-gradient flat-plate (ZPGFP) is used to demonstrate the accuracy and the robustness of the approach. To verify the reliability and applicability of the method, a two-dimensional particle image velocimetry (PIV) measurement was performed in a ZPGFP TBL with the low-to-moderate Reynolds number (Re). Via utilizing the algorithm of single-pixel ensemble correlation (SPEC), the velocity profiles in the ZPGFP TBL were resolved at a significantly improved spatial resolution, which greatly enhanced the measurement accuracy and permitted to accurately capture the near-wall velocity information. The accuracy of the approach is then quantitatively validated for the high Reynolds number turbulence by the ZPGFP TBL data. The research demonstrates that the current method can provide the precise estimation of wall friction with a mean error of less than 2%, which not only possesses the advantage of its insensitivity to the absolute wall-normal distance of the measuring point, but also is capable of providing an accurate prediction of wall shear stress based on fairly sparse experimental data on the velocity profile. The current study demonstrates that the wall shear stress can be accurately estimated by a velocity even at a single-point either measured or calculated in the near-wall region.