The application of hydrogeophysical techniques to delineating aquifers was conducted in De Aar, the eastern part of the Karoo region, Northern Cape, South Africa. Previously, recharge estimations in this region assumed a uniform aquifer type, overlooking the presence of diverse aquifer systems. This study identified both unconfined and confined aquifers to improve recharge potential assessments. Vertical electrical resistivity sounding (VES) and ground telluric methods were applied. Six VES stations and eleven profiles were measured using a 1D Wenner array configuration. The VES data, processed with IPI2win software, generated a 2D subsurface model. In contrast, the telluric data were analyzed using an automated algorithm to create a 2D profile. The electric potential difference curve was interpreted in comparison with lithological cross-sections. The VES results revealed three to four distinct layers of low-resistivity (0.9–8.1 Ωm), moderate-resistivity (22.4–125 Ωm), and high-resistivity (68–177 Ωm) values, indicating three lithological formations. The telluric data suggested that shallow groundwater boreholes were located in areas with groundwater levels above 50 m. These findings, which matched the lithological data, pointed to a double-layer aquifer system, suggesting that recharge estimates should be carried out to different aquifer layers. The study demonstrated how hydrogeophysical methods can effectively delineate aquifer systems and enhance the identification of recharge areas.
Application of aquifer delineation using hydro-geophysical techniques was conducted in De Aar, the eastern part of the Karoo region, Northern, South Africa. This study is aimed at demonstrating the use of hydrogeophycal techniques in delineating aquifer systems into unconfined and confined to estimate areas and zones likely to control ground-water recharge. An integrated hydrogeophysical approach using vertical electrical resistivity sounding (VES) and ground telluric methods was applied to delineate subsurface structures. Six VES surveys and seven profile surveys were measured using a Wenner array configuration and ground telluric method respectively. VES data was processed using IPI2win software and used to produce a 2D inference of the subsurface electrical resistivity model. The telluric passive surveys were processed through an automated in-built algorithm to generate 2D profile maps while the electric potential difference curve was interpreted with the lithological cross section constructed 2D conceptual model. The VES results showed four significant layers of low (0.9-8.1 Ωm), moderate (22.4-125 Ωm), and high 68-177 Ωm) electrical resistivity values which are suggestive of the different lithological formations. Additionally, the subsurface model from ground telluric methods supported shallow groundwater potential boreholes with the inference of fewer groundwater accumulations below 50 m. These hydrogeophysics results were compared to the drill chip lithological results and both suggested a double-layer aquifer system, which may therefore suggest that recharge estimation needs to be carried out in two different aquifers. The study therefore successfully demonstrated the use of geophysics techniques in delineating aquifer systems, thereby enhancing the identification of potential recharge areas.
The precise and accurate use of aquifer hydraulic parameters for assessing local and regional recharge potential for enhancing groundwater allocation planning is vital for many hydrogeological studies. The conventional approach for allocating groundwater presents a challenging scenario, as it remains uncertain whether the applied recharge estimate is local or regional recharge. The approach does not account for the extent of the aquifer recharge in terms of local and regional scale; instead, it assumes that recharge is distributed across the catchment. This study aimed to demonstrate the use of aquifer hydraulic parameters (transmissivity and storativity) to explain areas of potential recharge (local and regional) for enhancing groundwater allocation planning with a specific case study of De Aar, Northern Cape, South Africa. It argues that not integrating local and regional recharge potentials in planning for groundwater allocations can result in over- or under-allocation of groundwater resources to users. A constant discharge pumping test and recovery test matching the duration of pumping were conducted for data collection. The Flow Characteristics method was used as a diagnostic tool to understand the different aquifer flow regimes in the study area. To develop an integrated understanding of the groundwater system, a hydrogeological conceptual model was used to visualize areas with higher or lower recharge potential across local and regional scales. Results showed significant variability in transmissivity, ranging from 213 to 596 m2/d, and storativity, ranging from 0.0000297 to 0.000185. The transmissivity values suggest that groundwater moves faster; meanwhile, the storativity values suggest that the aquifer system has high water storage capacity. These results will assist water resource planners in making informed decisions on how to allocate groundwater to users. This study demonstrated that aquifer hydraulic parameters are a valuable tool for improving groundwater allocations, thereby highlighting the importance of considering areas for potential recharge, both local and regional, in planning groundwater allocation.
One of the principal environmental concerns relating to coal combustion waste disposal is the potential for groundwater contamination from salt fluxes and trace elements that may be leached into the underlying groundwater system. Since changes in moisture and salt concentrations usually provide contrasts in electrical properties against the host media, electrical resistivity methods can be used to monitor ingression of solute plumes as well as to detect any preferential flow paths within the ash medium. In this study, 2D electrical resistivity tomography was used to monitor brine (10% NaCl) water ingression through the unsaturated zone of a dry coal ash dump at a power station, Mpumalanga, South Africa. This was after the initial laboratory determination of the relation between electrical resistivity and moisture/salt content for the ash dump. The results showed that infiltration plume progression was more pronounced in the vertical direction, suggesting that moisture movement is mainly due to gravitational pull. There was no evidence of preferential flow within the ash medium, although the different infiltration rates for different sites suggested different permeability within the unsaturated zone. Keywords: coal ash dumps, brine infiltration, cementation factor, electrical resistivity tomography, time lapse survey