Diyaframla sac şekillendirme havacılıkta yaygın olarak kullanılan bir şekillendirme yöntemidir. Bu işlemde sac kalıba tutturulur, form makinesine yerleştirilir ve gaz basıncı uygulanır. Gazın etkisiyle şişen diyafram, basıncı sac yüzeyine ileterek kalıbın şeklini almasını sağlar. Bu yöntemde işlem sonunda sac metalde ortaya çıkan davranışlardan biri de geri esnemedir. Kalıp tasarımı bu esneme miktarı dikkate alınarak gerçekleştirilir. Geri esneme miktarında öne çıkan parametrelerden bazıları büküm yarıçapı, büküm açısı, malzeme kalınlığı ve malzeme türüdür. Çalışmamızda havacılık sektöründe yaygın olarak kullanılan 15-5PH paslanmaz çeliğin diyaframla şekillendirilmesinde geri esneme davranışı incelenmiştir. Deneysel çalışmalar için malzeme kalınlığı 0,813 mm, 1,27 mm, 1,6 mm ve 2 mm olarak belirlenmiştir. Çalışma sonunda 15-5PH malzemede proses parametrelerine bağlı olarak geri esneme oranını %90'ın üzerinde doğrulukla veren matematiksel bir ifade elde edilmiştir. Ayrıca çalışma parametrelerinin geri esneme davranışı üzerindeki temel etkileri Taguchi’nin L32 tasarımı temelinde ANOVA ile belirlenmiştir.
18 April 2024 in Transactions of the Indian National Academy of Engineering
Powder Bed Fusion–Laser Beam (PBF-LB) has emerged as a leading additive manufacturing technique for producing complex metallic components; however, its susceptibility to process-induced defects, particularly porosity, continues to limit its widespread application. In this study, a physics-informed computational framework was developed to predict porosity formation in Ti-6Al-4V parts by explicitly resolving transient thermal fields, melt pool dynamics, and layer-wise liquid fractions with temperature-dependent material properties. A dedicated graphical user interface was implemented, providing flexibility in defining the critical processing variables in PBF-LB. Model validation was performed using experimentally reported datasets from the literature. Benchmarking against melt pool geometries demonstrated that the algorithm successfully reproduced the depth and width evolution under different laser powers (100–195 W) and scan speeds (500–750 mm/s). Further comparisons with porosity data revealed strong quantitative consistency: for example, a numerical prediction of 0.19% porosity closely matched Archimedes (0.115%) and µ-CT (0.070%) results, while micrograph-based measurements indicated a higher value (0.204%). Across all investigated specimens, the algorithm reliably reflected experimentally observed porosity trends, including near fully dense conditions (
10 September 2026 in Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications
This study investigated the effects of Hot Isostatic Pressing (HIP) and gas nitriding on the microstructure, hardness, and tribological behavior of Ti6Al4V alloy fabricated by Electron Beam Melting (EBM). As-built specimens exhibited a lamellar α + β microstructure governed by the EBM thermal history. HIP treatment caused no significant α-lamellae coarsening; instead, it produced a more homogeneous phase distribution and slight lamellar refinement, indicating diffusion-driven phase redistribution. In contrast, gas nitriding led to the formation of a dense TiN/Ti 2 N surface layer, resulting in a pronounced gradient in both microstructural and mechanical properties between the surface and the bulk. Microhardness measurements revealed that the hardness decreased from approximately 380 HV in the as-built condition to around 320 HV after HIP treatment, corresponding to a reduction of about 15.8%. In contrast, gas nitriding significantly increased the surface hardness to approximately 540 HV, representing an improvement of nearly 42.1%. Tribological results showed that the average coefficient of friction decreased from 0.44 for the as-built samples to 0.38 after HIP treatment, corresponding to a reduction of 13.6%, and further decreased to approximately 0.10 after nitriding, indicating a substantial improvement of about 77.3%. The findings indicate that the response of EBM-fabricated Ti6Al4V to post-processing is governed by diffusion-based kinetics and the initial microstructure. While nitriding markedly enhances surface hardness and frictional performance, the observed surface cracking and localized delamination indicate an increased susceptibility of the hardened nitride layer to brittle damage under sliding conditions.
31 August 2026 in International Journal of 3D Printing Technologies and Digital Industry
Fused Deposition Modeling (FDM) of ABS is a cost-effective and versatile additive manufacturing technique; however, it is often constrained by residual stresses and poor surface finish, limiting its applicability in dimensionally critical components. Controlled heat treatment as a post-processing approach can relieve internal stresses and improve interlayer bonding, yet its combined effect on dimensional accuracy, mechanical performance, and surface quality remains insufficiently quantified. In this study, an experimental study combined with statistical analysis was conducted to investigate the effects of annealing temperature (100–140 °C) and holding time (20–60 min) on the dimensional stability, tensile strength, and surface roughness (Ra) of FDM-printed ABS specimens. Dimensional changes were expressed through the Dimensional Stability Index (DSI), tensile properties were measured according to ASTM D638, and surface roughness was characterized via contact profilometry. A Response Surface Methodology (RSM) approach coupled with Analysis of Variance (ANOVA) was employed to model and interpret the parameter effects. The results showed that temperature is the dominant factor influencing both DSI and tensile strength. The DSI values were minimal at 100 °C, showed moderate dimensional deviation at 120 °C, and increased sharply at 140 °C, demonstrating pronounced warpage and shrinkage near higher annealing temperatures. Tensile strength increased from 26.74 MPa in the untreated condition to a maximum of 30.82 MPa after annealing at 140 °C for 60 min, corresponding to a 15.3% improvement. In contrast, holding time showed a comparatively minor influence within the studied range. Although the minimum Ra was 4.72 µm at 120 °C for 40 min, representing a 30.1% decrease compared with the untreated specimens, surface roughness showed no statistically significant dependence on temperature or time. These findings demonstrate that controlled annealing can substantially enhance the mechanical performance of FDM-printed ABS parts, while moderate temperatures are preferable when dimensional accuracy must be preserved.