This study presents an effective strategy to enhance the efficiency and stability of perovskite solar cells (PSCs) by integrating neodymium-doped upconversion nanoparticles (UCNPs) coated with a TiO₂ shell into the mesoporous electron transport layer. The incorporation of neodymium (Nd³⁺) as a novel sensitizer shifts the near-infrared (NIR) absorption band away from the water vapor absorption region in the solar spectrum. This modification enables UCNPs to efficiently convert NIR light into ultraviolet (UV) and blue wavelengths, which are readily absorbed by TiO₂, generating additional charge carriers and improving photovoltaic performance. The optimized PSCs, fabricated by blending 30% UCNPs@TiO₂ with commercial TiO₂ paste, achieved a peak power conversion efficiency (PCE) of 21.71%, representing a 20.4% improvement over the control (18.04%). This enhancement included a 0.9% increase in the open-circuit voltage (V_oc), a 6.6% rise in the short-circuit current density (J_sc), and an 11.9% boost in the fill factor (FF). Additionally, the optimized PSCs exhibited remarkable stability, retaining over 90% of their initial PCE after 900 h in humid conditions, compared to only 70% for the control. These improvements result from enhanced light absorption, reduced moisture infiltration, and lower defect-related recombination. This approach provides a promising pathway for developing highly efficient and durable PSCs.

We report an advanced passivation strategy for perovskite solar cells (PSCs) by introducing core–shell structured perovskite quantum dots (PQDs), composed of methylammonium lead bromide (MAPbBr₃) cores and tetraoctylammonium lead bromide (tetra-OAPbBr₃) shells, during the antisolvent-assisted crystallization step. The epitaxial compatibility between the PQDs and the host perovskite matrix enables effective passivation of grain boundaries and surface defects, thereby suppressing non-radiative recombination and facilitating more efficient charge transport. At an optimal PQD concentration of 15 mg/mL, the modified PSCs demonstrated a remarkable increase in power conversion efficiency (PCE) from 19.2% to 22.85%. This enhancement is accompanied by improved device metrics, including a rise in open-circuit voltage (Voc) from 1.120 V to 1.137 V, short-circuit current density (Jsc) from 24.5 mA/cm² to 26.1 mA/cm², and fill factor (FF) from 70.1% to 77%. Spectral response analysis via incident photon-to-current efficiency (IPCE) revealed enhanced photoresponse in the 400–750 nm wavelength range. Additionally, long-term stability assessments showed that PQD-passivated devices retained more than 92% of their initial PCE after 900 h under ambient conditions, outperforming control devices which retained ~80%. These findings underscore the potential of in situ integrated PQDs as a scalable and effective passivation strategy for next-generation high-efficiency and stable perovskite photovoltaics.

Flexible perovskite solar cells (FPSCs) hold great promise for lightweight and wearable photovoltaics, but improving their efficiency and durability under mechanical stress remains a key challenge. In this work, we fabricate and characterize flexible planar FPSCs on a polyethylene terephthalate (PET). A phenethylammonium iodide (PEAI) surface passivation layer is introduced on the perovskite to form a two-dimensional capping layer, and its impact on device performance and stability is systematically studied. The champion PEAI-passivated flexible device achieves a power conversion efficiency (PCE) of ~16–17%, compared to ~14% for the control device without PEAI. The improvement is primarily due to an increased open-circuit voltage and fill factor, reflecting effective surface defect passivation and improved charge carrier dynamics. Importantly, mechanical bending tests demonstrate robust flexibility: the PEAI-passivated cells retain ~85–90% of their initial efficiency after 700 bending cycles (radius ~5 mm), significantly higher than the ~70% retention of unpassivated cells. This work showcases that integrating a PEAI surface treatment with optimized electron (SnO₂) and hole (spiro-OMeTAD) transport layers (ETL and HTL) can simultaneously enhance the efficiency and mechanical durability of FPSCs. These findings pave the way for more reliable and high-performance flexible solar cells for wearable and portable energy applications.