This paper investigates the problem of stability in a group of headings driven in high horizontal stress fields in the copper ore mines of the Legnica-Glogow Copper Belt (LGCB). The headings are protected with the roof bolting system. This problem is of high importance due to special safety regulations which apply in mining workings serving as airways and haulageways. The analysis was performed for a group of four headings driven in the geological and mining conditions of the Polkowice-Sieroszowice mine. The stability of the headings was evaluated with the use of Finite Element Method (FEM). The parameters of the rocks used in the numerical modeling have been determined on the basis of the Hoek–Brown classification, with the use of the RocLab 1.0 software. The parameters of the stress field have been identified on the basis of in situ measurements, which were performed in the Polkowice-Sieroszowice mine in 2012. The measurements were carried out with the use of the overcoring method, which is a stress relief method. A CSIRO HI probe was used as the measuring device. The tests were carried out on three measuring points, on which six successful tests were performed. The measurements confirmed the presence of high horizontal stresses in the rock mass. Numerical modeling was performed using the Phase2 v.8.0 software, in a triaxial stress state and in a plane strain state. The rock mass was described with an elastic-plastic model with softening. Numerical analyses were based on the Mohr–Coulomb failure criterion. It was assumed that the optimal measure of the stability of the group of headings is the range of the formed zone of yielded rock mass in the excavation roof. Numerical simulations have shown that the direction of driving the headings in the field of increased horizontal stresses may be of key importance for the stability of the headings in LGOM mines. The greatest extent of the yielded rock mass zone in the excavation roof occurred when the group of headings was driven in the direction perpendicular to the direction of the maximum horizontal stress component σ_H. The obtained results served to provide an example of the application of a roof bolting system to protect headings driven in unfavorable conditions in a high horizontal stress field.

In the polish underground copper mines owned by KGHM Polska Miedz S.A, various types of room and pillar mining systems are used, mainly with roof deflection, but also with dry and hydraulic backfill. One of the basic problems associated with the exploitation of copper deposits is rockburst hazard. Aa high level of rockburst hazard is caused by mining the ore at great depth in difficult geological and mining conditions, among others, in the vicinity of remnants. The main goal of this study is to investigate how hydraulic backfill improves the geomechanical situation in the mining filed and reduce rockburst risk in the vicinity of remnants. Numerical modeling was conducted for the case study of a mining field where undisturbed ore remnant, 40 m in width, was left behind. To compare the results, simulations were performed for a room and pillar mining system with roof deflection and for a room and pillar mining system with hydraulic backfill. Results of numerical analysis demonstrate that hydraulic backfill can limit rock mass deformation and disintegration in the mining field where remnants have been left. It may also reduce stress concentration inside or in the vicinity of a remnant, increase its stability, as well as prevent and reduce seismic and rockburst hazards. Hydraulic backfill as a local support stabilizes the geomechanical situation in the mining field.

Experience gained until now underground mining worldwide and in Poland indicates that remnants may have an impact on the occurrence of seismic phenomena. Remnants are stress concentration sites encompassing both the deposit and the layers of rock mass located above and below the undisturbed rock. In the case where stresses in the remnant exceed its strength, it may collapse, and under unfavourable geomechanical conditions, stress-induced rockburst may occur. Remnants may also cause breaking of strong roof layers above their edges, which results in the occurrence of high-energy shocks (Salustowicz [30], Adach [3], Adach and Butra [4]). This article presents the possibility of utilizing numerical modeling to evaluate the influence of remnant upon the occurrence of seismic phenomena. The results of numerical calculations performed for a model room-and-pillar mining system with roof deflection under the conditions of copper ore mines in the Legnica-Głogów Copper District (LGOM) are presented. Numerical calculations in a plane strain state were performed by means of Phase2 v. 8.0 software for the analyzed mining system in which remnant was left behind. The results of numerical modeling showed that sudden fracturing of roof layers above the mined out space may occur on the edge of the remnant. This may cause a shock with very high energy, and under the appropriate conditions, this may lead to the rockburst phenomenon.

The values of primary stresses are not allowed for as a criterion in the selection of roof bolting systems in mining excavations located at various depths in Polish copper ore mines. Therefore, in order to ensure enduring and safe operation of excavations, in particular, those driven in unfavourable geological and mining conditions, this problem has required solutions based on numerical methods. This article presents an example of applying numerical simulations to the evaluation of the stability of headings in Polish copper ore mines. The analyses included mining excavations located at various depths in the rock mass. This issue is of great importance, as safety regulations are prioritised in mining excavations which remain in operation even for several decades. The stability of the headings was evaluated with the use of the RS2 specialist numerical simulation software. This computer program uses the finite element method (FEM) for calculations. The rock parameters used in the numerical models have been determined on the basis of the Hoek–Brown classification. For that purpose, the RocLab 1.0 software was used. The parameters of the stress field were identified from the profile of the GG-1 shaft with the assumed hydrostatic state of stress. The numerical modelling was performed in a triaxial stress state and in a plane strain state. The numerical analyses were based on the Mohr–Coulomb failure criterion. The rock medium was described with the elastic-plastic model with softening (roof and walls) and with the elastic-plastic model (floor). The results of the numerical analyses served to provide an example of the application of a roof bolting system to protect headings located at the depths of 1000 m b.g.l. and 1300 m b.g.l.

This paper concerns the issue of selecting appropriate stress field parameters for predicting the stability of headings driven under the geological and mining conditions of Polish underground copper mines. The problem is of key importance due to strict safety requirements in mine workings that serve ventilation and transport functions. Numerical analyses were carried out for four stress field variants: the stress state determined based on Bulin’s formulas (variant 1), the hydrostatic stress state (variant 2), and stress states determined from in situ measurements conducted in the Rudna mine (variant 3 and variant 4). Numerical simulations were performed for a group of four headings, supported with fully grouted rock bolts, in the geological and mining conditions of the Rudna mine. Stability assessment was performed using the finite element method (FEM). Rock mass input parameters for the modeling were obtained with RocLab 1.0, applying the Hoek–Brown classification, while numerical analyses employed the Mohr–Coulomb failure criterion. The elastic–plastic model with softening was used to describe the rock mass behaviour. Numerical calculations were conducted in the RS2 computer program in a triaxial stress state and in a plane strain state. The range of the yielded rock mass zone in the roof of the headings was assumed as the optimal measure of the headings stability. The obtained simulation results provided a basis for recommending suitable rock bolting systems to protect the stability of headings developed under various initial stress field conditions.

Istotnym problemem związanym z polskim górnictwem podziemnym jest prowadzenie eksploatacji na coraz większych głębokościach, w trudnych warunkach geologiczno-górniczych, w tym w obszarach oddziaływania resztek złoża. Dotyczy to zarówno podziemnych kopalń węgla kamiennego jak i rud miedzi. Głównym celem artykułu jest zbadanie, w jaki sposób resztki złoża o różnych wielkościach wpływają na sytuację geomechaniczną w polu eksploatacyjnym. W artykule przeprowadzono symulacje numeryczne dla pola eksploatowanego systemem komorowo-filarowym, w którym pozostawiono nienaruszone reszki złoża o szerokościach 10 m, 20 m, 40 m, 60 m, 100 m i 200 m. Wyniki analiz numerycznych wskazują, że wielkość pozostawionej resztki złoża ma znaczący wpływ na rozkład naprężeń oraz stateczność górotworu w polu eksploatacyjnym. Wraz ze zmniejszaniem szerokości resztki naprężenia pionowe (σy) zarówno wewnątrz resztki, jak i w jej otoczeniu wzrastają, osiągając bardzo wysokie wartości dla wąskich resztek. W przeciwieństwie do naprężeń pionowych (σy), współczynnik wytrzymałości (Sf) maleje wraz ze zmniejszaniem szerokości resztki. Symulacje wykazały również, że pozostawienie dużej resztki calizny w formie filara stabilizującego poprawia stateczność stropu w polu eksploatacyjnym. Jednak w przypadku resztek o znacznej szerokości, w warstwach stropu nad krawędzią resztki od strony zrobów, może powstać strefa niestabilna, skutkująca wystąpieniem nagłego pęknięcia i zniszczenia sztywnych warstw stropowych na krawędzi resztki. Przy niesprzyjających warunkach może doprowadzić to do wystąpienia zjawiska dynamicznego. Uzyskane w niniejszym artykule wyniki mogą zostać wykorzystane do poprawy bezpieczeństwa i zwiększenia efektywności eksploatacji złóż rud miedzi.