Alessandro Dell'Amico

Dr. Alessandro Dell'Amico

orcid

Research Focus & Metrics

Academic Career Length

14Years (2013-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
10 February 2016 in International Journal of Fluid Power
Verified
Journal Article
Closed access
ADAlessandro Dell'Amico
Alessandro Dell'Amico
PKPetter Krus
Petter Krus
This paper investigates the static and dynamic behaviour of a pressure control valve with nonlinear negative characteristics. The pressure control valve has both reducing and relieving capability and is actuated by a solenoid. The static characteristics have been measured over the entire working range, covering the dynamic response of the solenoid, as well as the complete valve. A model is proposed that considers the flow as a mix of laminar and turbulent flow and flow forces with a flow angle that varies with the stroke of the spool. The model shows good agreement with measurements. The investigations show that the flow forces decrease with higher flow rates as a result of a flow angle that tends to go towards a vertical angle. This results in an increase in pressure with flow during pressure reducing mode. A linear analysis is also presented, explaining this as a negative spring constant in the low frequency range. Stability is, however, maintained.

24 December 2024 in Aerospace
Verified
Journal Article
Open access
PDF file
ADAlessandro Dell'Amico
Alessandro Dell'Amico
CRChristopher Reichenwallner
Christopher Reichenwallner
This paper presents a methodology for evaluating different flight control actuation system architectures in the early conceptual design phase. In particular, this paper shows how hydraulic and electric actuators can be modeled even if very little is known about the aircraft design or requirements while still including the most dominant static and dynamic characteristics. Singular Value Decomposition is used to estimate model parameters and actuator characteristics from industrial data. This is a quick way to estimate what is needed with little input. The purpose of the models is to predict the power consumption, cooling needs, weight, and size. This is performed by integrating the actuator models in a dynamic simulation framework that also includes a flight simulator and surrounding systems. The results from subsystem studies support the aircraft design process, where actuator characteristics affect the engine performance and aircraft sizing. The methodology is applied to a generic fighter by comparing hydraulic and electric actuation system architectures. Besides providing a generic approach to the actuator modeling, the parameters that affect both the static and dynamic characteristics of an electromechanical and electrohydrostatic actuator are estimated with reasonably good accuracy with only four design parameters as input.

9 September 2013
Verified
Conference Paper
Open access
PDF file
ADAlessandro Dell'Amico
Alessandro Dell'Amico
MCMarcus Carlsson
Marcus Carlsson
ENErik Norlin
Erik Norlin
MSMagnus Sethson
Magnus Sethson
Here is information on how to publish, spread your research, and search for your publications. Most of LiU's research publications are directly imported into DiVA from the Web of Science. Before registering a publication, always check if the publication is already in DiVA!

25 June 2024 in Actuators
Verified
Journal Article
Open access
PDF file
ADAlessandro Dell'Amico
Alessandro Dell'Amico
This paper presents the design and implementation of the hardware and control strategies of an electrohydraulic air load simulation system for testing aerospace actuators. The system is part of an Iron Bird, which is an energy management research platform developed in collaboration between Saab AB and Linköping University. The purpose of the air load system is to provide realistic forces on the test object through the integration of a flight simulator for full mission evaluation. The challenge with electrohydraulic force control is tackled by increasing the hydraulic capacitance from increased load cylinder dead volumes, together with a feed-forward link based on accurate modelling of the test object and load system by adopting an optimisation routine to find model parameters. The system is implemented for both an electromechanical and servohydraulic actuator as test objects with different performance requirements. The control design is based on nonlinear and linear modelling of the system, and experimental test data are used to tune the models. Finally, test results of the air load system prove its force-tracking performance.

28 October 2025 in Swedish Aerospace Conference, FT2025
Verified
Conference Paper
Open access
PDF file
ADAlessandro Dell'Amico
Alessandro Dell'Amico
TGTúlio De Abreu Burgos Gonçalves
Túlio De Abreu Burgos Gonçalves
YCYasmin Soares Castro
Yasmin Soares Castro
ASAndrew Saramento
Andrew Saramento
WOWesley Oliveira
Wesley Oliveira
PKPetter Krus
Petter Krus
This paper presents the initial work of an international collaboration with the aim of connecting distributed test rigs for evaluation of new flight control actuation system technologies. The involved partners are companies, universities, and institutions from Sweden and Brazil. Three test rigs with different capabilities and scopes are available through the partners involvement in the project, that includes an industrial robot-based flight simulator, a test rig for digital hydraulic actuators, and a full-scale Iron Bird for energy management and flight control actuation system testing. Connecting the test rigs facilitates a larger test scope and the evaluation of several technologies than using only one test rig. A model-based approach is adopted surrounding a virtual flight simulator used for model integration to allow testing both actuator performance and HMI aspects. The test case is a fictive fighter aircraft. The virtual flight simulator includes the aircraft behaviour, aerodynamics, propulsion, and flight control system. The virtual flight simulator is implemented in the physical one, and two flight missions are defined and flown by trained pilots. The generated data set is used by the actuator test rigs for performance evaluation. In the final part the actuator models are validated using the test data and integrated in the physical flight simulator for evaluating the impact of the actuator characteristics on aircraft performance and handling. The paper outlines the framework and method and illustrates the first part of the distributed testing by integrating pilot generated flight data for actuator performance evaluation and comparison.

1 January 2025
Verified
Conference Paper
Open access
PDF file
ARAmy Rankka
Amy Rankka
ALAless
Aless
RDRo Dell’amico
Ro Dell’amico
ADAlessandro Dell'Amico
Alessandro Dell'Amico
Operator assistance functions for working machines such as loader cranes are often developed with the aim of increasing the productivity of an unskilled operator or of increasing the safety of operating the machine. For a kinematically redundant system, such as the boom system of a loader crane where three joints are used to control a motion in a two dimensional plane, the operator assistance functions can also be developed with an energy efficiency objective. In this paper, the semi-automatic function Crane Tip Control (CTC) for loader cranes is considered. The energy required to perform a CTC motion depends on the pressure levels and flow demand of each active cylinder and how this is translated into pump pressure and flow. Previous research has shown that the current CTC strategy is not optimal with regards to energy efficiency. In this work, CTC controllers for limited working areas are developed where the strategy is decided by a neural network trained by a Reinforcement Learning approach with an energy minimizing objective on a simulation model of the crane. A dynamic programming (DP) algorithm that can find near-optimal solutions for given trajectories offline has been developed in previous research. The energy performance of the new controllers with neural networks, NN controllers for short, are benchmarked on a number of test cases by comparing the solutions to those of the DP algorithm, denoted DP controllers. The results show that energy consumption of the new controllers are only up to 2.2 % higher than the consumption of the DP controllers. The methodology is thus promising, but future work is required to expand it to cover the complete working envelope of the CTC function.