Palm trees are very fast-growing species. Their management produces annually a large amount of biomass that traditionally has been either disposed of at dumping sites or has been burnt onsite. This paper presents an experimental study to obtain particleboard using this biomass in a low energy process (short pressing time and low pressing temperature), using particles of different sizes from the rachis (midrib) of the three palm species most representative of urban gardening in Spain: canary palm (Phoenix canariensis hort. ex Chabaud), date palm (Phoenix dactylifera L.) and washingtonia palm (Washingtonia robusta H. Wendl). Their physical and mechanical properties were tested, and the feasibility of their use as a construction material was evaluated. The results showed that the manufactured particleboard had similar performance to conventional wood particleboard and good thermal insulation properties. Boards made with the canary species showed better mechanical performance. The properties of the particleboard depended on the particle size and species. The use of the pruning waste of palm trees to produce durable materials such as particleboard could be beneficial to the environment since it is a method of carbon fixation, helping to decrease atmospheric pollution and reducing the amount of waste that ends in dumping sites.
The raw materials used to manufacture thermal insulation in buildings consume a large amount of energy and are not generally biodegradable, which means it is necessary to increase the use of renewable, eco-friendly resources such as plant fibers in order to reduce the environmental problems this generates. The wood adhesives developed by the petrochemical industry offer excellent performance and are affordable. However, their use has an expiry date and in the future they will be rejected due to the environmental and health problems they can cause. The objective of this work was to develop a new eco-friendly biocomposite that could be used for thermal insulation in buildings. Boards were manufactured from giant reed particles with a particle size of 2 to 4 mm, using 5 and 10% by weight of citric acid as a natural binder. Experiments were then carried out to investigate the effect of board density on mechanical, physical, and thermal properties. A new type of composite was obtained with a thermal conductivity of 0.081–0.093 W/m K, which makes it suitable as an insulating material. The boards with a density of 850 kg/m3 had a modulus of rupture (MOR) of 12.5 N/mm2, a modulus of elasticity (MOE) of 2440 N/mm2, and an internal bonding strength (IB) of 0.61 N/mm2, and they could be used as insulation panels for divisions and enclosures in buildings.
This paper presents an experimental study on the bond behaviour of cement panels reinforced with plant fibres from the recycling of waste jute bags, using starch as a plasticiser. During processing, different proportions of jute (5 wt %, 10 wt %, 15 wt %, and 20 wt %) were used with respect to the weight of cement, and the mixture was exposed to a pressure of 2.6 MPa and a temperature of 100 °C. The density, swelling thickness, internal bonding, flexural strength, and thermal conductivity were studied. Mechanical tests indicated that the values of the modulus of rupture (MOR) and the modulus of elasticity (MOE) increased over time; thus, the jute particles appeared to be protected by the plasticised starch and no degradation was observed. At 28 days, the particleboard with 5% starch had an MOR of 12.82 MPa and an MOE of 3.43 GPa; these values decreased when the jute proportion was higher. The thermal conductivity varied from 0.068 to 0.085 W·m−1·K−1. The main conclusion is that jute-cement-starch composite panels can be manufactured with physical, mechanical, and thermal properties that meet the European standards for use in the construction of buildings as partitions, interior divisions, and thermal insulators.
Traditionally, plant fibres have been used as a raw material for manufacturing construction materials; however, in the last century, they have been replaced by new mineral and synthetic materials with manufacturing processes that consume a large amount of energy. The objective of this study was to determine the mechanical, physical and acoustic properties of panels made from giant reed residues. The article focuses on evaluating the acoustic absorption of the boards for use in buildings. The materials used were reed particles and urea–formaldehyde was used as an adhesive. The panels were produced with three particle sizes and the influence that this parameter had on the properties of the board was evaluated. To determine the absorption coefficient, samples were tested at frequencies ranging from 50 to 6300 Hz. The results showed that the boards had a medium absorption coefficient for the low and high frequency range, with significant differences depending on the particle size. The boards with 2–4 mm particles could be classified as Class D sound absorbers, while boards with particle sizes of 0.25–1 mm showed the greatest sound transmission loss. Unlike the acoustic properties, the smaller the particle size used, the better the mechanical properties of the boards. The results showed that this may be an appropriate sound insulation material for commercial use.
The giant reed (Arundo donax L.) is considered one of the world’s 100 worst invasive species. The main method by which this species propagates is by growth of scattered fragments of rhizome, spreading without control with very strong, deep roots. Agricultural waste consists of lignocellulosic materials that can substitute natural wood and offer a suitable alternative with which to manufacture boards for furniture, packaging and building purposes. The objectives of this work were to obtain binderless particleboards using giant reed rhizome as the raw material, to evaluate their mechanical and physical properties according to the applicable European standards and to assess the self-binding mechanism of the particles in the board. Six types of boards (12 classes) were manufactured with giant reed rhizome biomass. They were manufactured with a temperature of 110 °C, a pressure of 2.5 MPa and pressing times of 7 and 15 min, applying one or two pressing cycles. The results achieved for modulus of rupture (14.2 N/mm2), modulus of elasticity (2052.45 N/mm2) and internal bonding strength (1.12 N/mm2) show that the mechanical properties were improved by using a smaller rhizome particle size and two pressing cycles.
Acoustic and thermal properties were determined for boards made from Washingtonia palm tree pruning waste. Three types of boards with different particle sizes (0.25 to 1.00 mm, 1.00 to 2.00 mm, and 2.00 to 4.00 mm) were obtained from the rachis of the palm fronds. To bind the particles, 8% urea formaldehyde resin was used via hot pressing at 120 ºC for 6 min at 1.6 MPa. Three types of panels were generated to evaluate the influence of particle size. Analysis of their physico-mechanical properties showed that their mechanical performance was superior to the existing insulating boards used in the building industry. The average thermal conductivity of the panels was 0.062 W/(K·m) and did not depend on the size of the particles. At frequencies of 125 and 250 Hz, the experimental boards were classified as class D acoustic panels. The manufactured panels had high values of sound transmission loss (TL), despite the thinness of the panels, which indicates that they have good acoustic insulation capacity. Acoustic properties could be improved by increasing the thickness of the boards. Due to their mechanical, thermal, and acoustic properties, these panels could be used as lining and as false ceilings.