The Sentinel-3 Mission Performance Centre (S3MPC) is tasked by the European Space Agency (ESA) to monitor the health of the Copernicus Sentinel-3 satellites and ensure a high data quality to the users. This paper deals exclusively with the effort devoted to the altimeter and microwave radiometer, both components of the Surface Topography Mission (STM). The altimeters on Sentinel-3A and -3B are the first to operate in delay-Doppler or SAR mode over all Earth surfaces, which enables better spatial resolution of the signal in the along-track direction and improved noise reduction through multi-looking, whilst the radiometer is a two-channel nadir-viewing system. There are regular routine assessments of the instruments through investigation of telemetered housekeeping data, calibrations over selected sites and comparisons of geophysical retrievals with models, in situ data and other satellite systems. These are performed both to monitor the daily production, assessing the uncertainties and errors on the estimates, and also to characterize the long-term performance for climate science applications. This is critical because an undetected drift in performance could be misconstrued as a climate variation. As the data are used by the Copernicus Services (e.g., CMEMS, Global Land Monitoring Services) and by the research community over open ocean, coastal waters, sea ice, land ice, rivers and lakes, the validation activities encompass all these domains, with regular reports openly available. The S3MPC is also in charge of preparing improvements to the processing, and of the development and tuning of algorithms to improve their accuracy. This paper is thus the first refereed publication to bring together the analysis of SAR altimetry across all these different domains to highlight the benefits and existing challenges.

This paper describes the demonstration of a regional high-resolution level-3 (L3) altimeter data unification and altimeter combination system (DUACS) developed with support from the French space agency (CNES). Deduced from full-rate (20 Hz to 40 Hz) level-2 (L2) altimeter measurements, this product provides sea level anomalies (SLA) and other essential physical variables at a spatial resolution of one sample every ~1 km over the North Atlantic Ocean. This allows us to resolve wavelengths from ~35 km to ~55 km depending on the altimeter considered. This was made possible by recent advances in radar altimeter processing for both synthetic aperture radar (SAR) and low-resolution-mode (LRM) measurements, as well as improvements made to different stages of the DUACS processing chain. Firstly, the new adaptive and low-resolution with range migration correction (LR-RMC) processing techniques were considered for Jason and Sentinel-3 (S3A), respectively. They significantly reduce errors at short wavelengths, and the adaptive processing also reduces possible land contamination near the coast. Next, up-to-date geophysical and environmental corrections were selected for this production. This includes specific corrections intended to reduce the measurement noise on LRM measurements and thus enhance the observability at short wavelengths. Compared with the 1 Hz product, the observable wavelengths reached with the demonstration high-resolution product are reduced by up to one third, or up to half in the northeast Atlantic region. The residual noises were optimally filtered from full-rate measurements, taking into consideration the different observing capabilities of the altimeters processed. A specific data recovery strategy was applied, significantly optimizing the data availability, both in the coastal and open ocean areas. This demonstration L3 product is thus better resolved than the conventional 1 Hz product, especially near the coast, where it is defined up to ~5 km against ~10 km for the 1 Hz version. Multi-mission cross-calibration processing was also optimized with an improved long-wavelength error (LWE) correction, leading to a better consistency between tracks, with a 9–15% reduction in SLA variance at cross-overs. The new L3 product improves the overall consistency with tide gauge measurements, with a reduction in SLA differences variance by 5 and 17% compared with the 1 Hz product from the S3A and Jason-3 (J3) measurements, respectively. Primarily intended for regional applications, this product can significantly contribute to improving high-resolution numerical model output via data assimilation. It also opens new perspectives for a better understanding of regional sea-surface dynamics, with an improved representation of the coastal currents and a refined spectral content revealing the unbalanced signal.

The SWOT satellite, carrying the KaRIN first wide-swath onboard altimeter, was launched in December 2022, and has now delivered more than a year of surface water elevation data over the ocean and inland lakes/rivers. These data are affected by systematic errors which constitute the dominant part of the error budget at scales larger than a few thousands of kilometers. Some strategies for their estimation and calibration were explored during the pre-launch studies with performance estimations. Now, based on the real data, we propose in this study to assess the systematic error budget with statistical methods relying on spectral and co-spectral analysis. From this assessment, suggesting very low error levels (below requirements), we propose the implementation of the calibration algorithms at Level-2 and Level-3 with a few minor adjustments justified by the error spectra. The calibrated products are then validated with usual CalVal metrics.

Over the past three decades, five satellites have succeeded one another on the reference orbit, building the longest continuous climate record of global sea level measurements. Its continuity is ensured thanks to tandem flights between consecutive satellites. In this paper, we demonstrate that the first satellite of the Sentinel-6 series (Sentinel-6 Michael Freilich) has enabled the detection of a processing anomaly in the Jason-1/2/3 ground segment. An inconsistency in the altimeter range reconstruction has been identified, causing its underestimation by 3.65 mm. At certain latitudes, determined by the satellite’s orbital velocity, the altimeter range shows no effect from the anomaly. For the reference orbit, the range is not affected at the poles, around the equator and, for ascending tracks, at 40° S. All Jason Geophysical Data Record (GDR) versions prior to GDR-G are impacted by the described processing anomaly. While a full reprocessing of the Jason data with the GDR-G standard is pending, this paper presents a latitudinal empirical correction to be applied to Jason datasets generated with GDR-F and earlier ground segments. This correction, to be applied on the altimeter range, is derived from one month of patched Jason-3 data and is intended for reference orbit only. Additionally, SWOT Nadir ground processing is also affected by the same processing error and has been corrected from the GDR-S2 version onward. Finally, our analysis shows a negligible impact of this processing anomaly on Jason Level-2-derived products, models and metrics.