Christian Ley

Prof. Dr. Christian Ley


Research Focus & Metrics

Academic Career Length

18Years (2009-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2019 in Polymer
Verified
Journal Article
Closed access
JCJulien Christmann
Julien Christmann
CLChristian Ley
Christian Ley
XAXavier Allonas
Xavier Allonas
AIAhmad Ibrahim
Ahmad Ibrahim
CCCéline Croutxé-Barghorn
Céline Croutxé-Barghorn

17 July 2013 in Journal of Polymer Science Part A: Polymer Chemistry
Verified
Journal Article
Closed access
PDF file
KKKoichi Kawamura
Koichi Kawamura
CLChristian Ley
Christian Ley
JSJulien Schmitt
Julien Schmitt
MBMaxime Barnet
Maxime Barnet
XAXavier Allonas
Xavier Allonas

31 August 2022 in Polymer Chemistry
Verified
Journal Article
Closed access
PDF file
JZJunyi Zhou
Junyi Zhou
LPLena Pitzer
Lena Pitzer
CLChristian Ley
Christian Ley
TRThomas Rölle
Thomas Rölle
XAXavier Allonas
Xavier Allonas
A new highly reactive photoinitiating system based on a penta-methine cyanine dye and a triarylalkylborate salt for radical photopolymerization reactions using near infra-red (NIR) light was investigated. The remarkably high reactivity is partly ascribed not only to the photochemical properties of the dye such as its very high absorption coefficients but also to the combination of the dye with the borate salt. Interestingly, the correlation between the borate salt concentration and the rate of polymerization can be displayed in a saturation graph. This effect is presumably caused by the formation of an ion-pair complex consisting of the cationic dye and anionic borate molecule in a medium of moderate polarity. It is shown that the association constant of such ion-pairs is quite high and, due to the short lifetime of the excited state of the dye, it is the only possible route for the generation of initiating radicals after excitation. Finally, it is found that the rate of polymerization correlates with the calculated rate of initiation, giving confidence to the proposed initiation mechanism. Advantageously, the high sensitivity of the new photoinitiating system allows for the use of a low LED light power of 40 mW cm−2 and thus supports a truly photonic mechanism of initiation instead of a thermal one.

4 August 2019 in ChemPhotoChem
Verified
Journal Article
Closed access
PDF file
BMBoris Metral
Boris Metral
ABAdrien Bischoff
Adrien Bischoff
CLChristian Ley
Christian Ley
AIAhmad Ibrahim
Ahmad Ibrahim
XAXavier Allonas
Xavier Allonas

7 January 2009 in Chemphyschem
Verified
Journal Article
Closed access
PDF file
CLChristian Ley
Christian Ley
FLFabien Lacombat
Fabien Lacombat
PPPascal Plaza
Pascal Plaza
MMMonique M. Martin
Monique M. Martin
Isabelle LerayIsabelle Leray
Isabelle Leray
BVBernard Valeur
Bernard Valeur

11 September 2019 in ChemPhotoChem
Verified
Journal Article
Open access
PDF file
DODennis Oprych
Dennis Oprych
CSChristian Schmitz
Christian Schmitz
CLChristian Ley
Christian Ley
XAXavier Allonas
Xavier Allonas
EEEugeny Ermilov
Eugeny Ermilov
BSBernd Strehmel
Bernd Strehmel
UCNPs based on NaYF4:Yb3+/Tm3+@NaYF4 generate blue (450 nm, 476 nm) and UV light (345 nm, 362 nm) upon exposure with a laser emitting at 980 nm. Time‐resolved measurements indicated the same origin of the emission monitored at 362 nm and 450 nm by a rise time of 226 μs while their decay occurs with a similar time frame of 260 μs. The observation can be attributed to an energy transfer where successive absorption of three photons results in population of the 1I6 state. Intensity‐dependent exploration of the up‐converted emission indicated a cubic dependence between the luminescence intensity If and laser intensity I (If ∝ I3) monitored at 362 nm and 450 nm. The emission at 345 nm involves successive excitation with four photons. The up‐converted light excites radical photoinitiators selected from Ivocerin, thioxanthone and camphorquinone where a coinitiator, sulfonium salt, helped to generate the initiating radicals. These different systems comprising the UCNP and the photoinitiator generate crosslinked materials based on urethane dimethacrylate (M1) as model monomer applying laser exposure at 980 nm. Real‐time FTIR monitoring of M1 exposed indicated a different initiation time as a function of the laser intensity applied. Stress relaxation measurements complemented the understanding between material parameters on the one side and loading with UCNPs, light intensity and kinetics on the other side.