Sining Li

Dr. Sining Li

orcid

Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
11 December 2024 in Molecules
Verified
Journal Article
Open access
PDF file
QCQiushuang Cui
Qiushuang Cui
YHYong Huang
Yong Huang
XMXufei Ma
Xufei Ma
SLSining Li
Sining Li
RBRuyun Bai
Ruyun Bai
HWHanyu Wei
Hanyu Wei
In this research, we produced two types of biochar (BC) using cotton stalks as raw material and KOH as an activator, and compared their performance and adsorption mechanisms in the removal of tetracycline (TC) and methylene blue (MB) from wastewater. The results showed that the biochar generated using both procedures formed pores that connected to the interior of the biochar and had extensive microporous and mesoporous structures. The molten salt approach produces biochar with a higher specific surface area, larger pore size, and higher pore volume than the impregnation method, with a maximum specific surface area of 3095 m2/g. KBCM-900 (the BC produced using the molten salt method at 900 °C) had a better adsorption effect on TC, with a clearance rate of more than 95% in 180 min and a maximum adsorption amount of 912.212 mg/g. The adsorption rates of the two BCs for MB did not differ significantly at low concentrations, but as the concentration increased, KBCI-900 (the BC generated by the impregnation method at 900 °C) exhibited better adsorption, with a maximum adsorption of 723.726 mg/g. The pseudo-second-order kinetic model and the Langmuir isotherm model may accurately describe the TC and MB adsorption processes of KBCI-900 and KBCM-900. The KBCI/KBCM-900 adsorption process combines physical and chemical adsorption, with the primary mechanisms being pore filling, π–π interactions, hydrogen bonding, and electrostatic interactions. As a result, biochar generated using the molten salt method is suitable for the removal of large-molecule pollutants such as TC, whereas biochar prepared using the impregnation method is suitable for the removal of small-molecule dyes such as MB.

28 September 2025 in Minerals
Verified
Journal Article
Open access
PDF file
LJLiran Jiao
Liran Jiao
YHYong Huang
Yong Huang
YZYingshuang Zhang
Yingshuang Zhang
SLSining Li
Sining Li
YLYubin Liu
Yubin Liu
LWLinlong Wei
Linlong Wei
High-purity quartz is a key material for photovoltaics, semiconductors, and optical fibers. The raw material for high-purity quartz mainly comes from natural crystal and pegmatite. It is an attractive research field to excavate alternative feedstocks for traditional materials. Quartz conglomerate is a coarse-grained, clastic sedimentary rock that is cemented by a secondary silica or siliceous matrix. Economically, quartz conglomerate is gaining attention as a strategic alternative to depleting high-grade quartz veins and pegmatites. In this study, high-purity quartz was prepared by purifying quartz conglomerate from Jimunai, Altay, Xinjiang. The method combined high-temperature roasting, water quenching, and ultrasonic-assisted acid leaching. The effects of process parameters on purification efficiency were systematically investigated with the aid of XRD, SEM-EDS, and ICP-OES quantitative element detection. Many cracks formed on the quartz during roasting and quenching. These cracks exposed gap-filling impurities. Gas–liquid inclusions were removed, improving acid leaching. Under optimal ultrasonic-assisted acid leaching conditions (80 °C, 4 h, 10% oxalic acid + 12% hydrochloric acid, 180 W), the Fe content decreased to 6.95 mg/kg, with an 85.6% removal rate. The total impurity content decreased to 210.43 mg/kg. The SiO2 grade increased from 99.77% to 99.98%. Compared to traditional acid leaching, ultrasonic-assisted acid leaching improved Fe removal and reduced environmental pollution.

27 July 2024 in Buildings
Verified
Journal Article
Open access
PDF file
YHYong Huang
Yong Huang
RYRui Yu
Rui Yu
JSJian Sun
Jian Sun
YLYubin Liu
Yubin Liu
SLSiyu Luo
Siyu Luo
SLSining Li
Sining Li
In recent years, with the development of the construction industry and the wide application of concrete materials, the demand for natural resources such as sand and gravel in China has continued to grow. The Xinjiang region is rich in natural desert sand resources due to its large desert area, which are inexpensive and easy to obtain, providing new possibilities for the production of concrete materials. The use of natural desert sand as concrete aggregate not only reduces the cost of construction but also contributes to the protection of the environment and the rational development and utilization of natural resources. However, poor particle gradation in natural desert sand leads to poor concrete properties. In this study, the Dinger–Funk equation was used to optimize the aggregate gradation of natural desert sand from Toksun, Xinjiang, and concrete specimens were prepared for mechanical properties and sulfate erosion resistance tests. The test results show that the four groups of aggregates optimized by the Dinger–Funk equation are better than the single gradation and natural gradation in terms of apparent density, bulk density, void ratio, mechanical properties, and durability of concrete. Where the distribution modulus n = 0.3 was the best, the compressive strength, splitting strength, and flexural strength were increased by 13.14%, 15.71%, and 11.08%, respectively, as compared to the natural gradation. After 90 sulfate erosion and dry–wet cycles, the mass change rate and relative dynamic elastic modulus of concrete specimens first increased and then decreased, and at the distribution modulus n = 0.3, the aggregate particles of 0.3–0.6 mm, 0.6–1.18 mm, and 1.18–2.36 mm accounted for 26.98%, 32.33%, and 40.69%, respectively, and the smallest of the mass change rates of durability was the best.

17 August 2024 in Applied Sciences
Verified
Journal Article
Open access
PDF file
SLSining Li
Sining Li
YHYong Huang
Yong Huang
JSJian Sun
Jian Sun
RYRui Yu
Rui Yu
YLYubin Liu
Yubin Liu
QCQiushuang Cui
Qiushuang Cui
In cold regions, saline soils can cause dissolution, settlement, and salt expansion of the roadbed under the influence of freeze–thaw cycles, so they need to be stabilized during road construction. In this study, lime, fly ash (FA), and polyacrylamide (PAM) were used to stabilize sulfate saline soils, and the stabilized saline soils were subjected to the unconfined compressive strength test (UCS), splitting test, and freeze–thaw cycle tests (FTs). The stabilization mechanism of the three materials on saline soils was also studied via scanning electron microscopy (SEM), X-ray diffraction (XRD), Fourier-transform infrared spectroscopy (FTIR), thermogravimetric analysis (TG), and X-ray photoelectron spectroscopy (XPS). The test results showed that the addition of lime, FA, and PAM to saline soils can improve the mechanical properties and frost resistance of saline soils. After 28 d of curing, the UCS of FA-, PAM-, and lime-stabilized saline soils increased by at least 55%, 23%, and 1068%, respectively, and the splitting strength increased by at least 161%, 75%, and 2720%, respectively. After five freeze–thaw cycles, the residual strength ratios (BDRs) of the UCS of L2 (lime 8%), F2 (FA 11%), and P2 (PAM 1%) stabilized soils and saline soils were 71.78%, 56.42%, 39.05%, and 17.95%, respectively, and the decreasing trend tended to be stable. The saline soils stabilized by lime and FA were chemically stabilized, and their mechanical properties and frost resistance were better than the physical stabilization of PAM.

30 January 2025 in Sustainability
Verified
Journal Article
Open access
PDF file
RBRuyun Bai
Ruyun Bai
YHYong Huang
Yong Huang
SLSining Li
Sining Li
CSChangzhi Su
Changzhi Su
HLHuan Li
Huan Li
YSYi Si
Yi Si
Xinjiang is one of China’s most significant energy bases, and the generated fly ash (FA) contains a high concentration of metallic elements that can be used as a valuable resource. In this study, we looked into a roasting-acid leaching process technique for efficiently extracting gallium metal (Ga) from FA, employing sodium fluoride (NaF) as the roasting auxiliary and citric acid inzter (C6H8O7) acid leaching. After high-temperature activation by NaF, the glassy phase of FA was converted into silica aluminate with excellent acid solubility, and Ga was extracted from FA via acid leaching. The effects of optimal roasting and acid leaching process conditions on the Ga leaching rate were investigated. The results showed that it exhibited 83.71% Ga extraction under the conditions of a roasting temperature of 850 °C, FA-NaF coordination ratio of 1:0.5, roasting time of 10 min, C6H8O7 solution concentration of 1.75 mol/L, ratio (S/L) of 1:15, acid leaching temperature of 100 °C, and acid leaching time of 1 h. The results also indicated that it was possible to obtain a higher extraction efficiency for the Ga extracts under the conditions of roasting temperature of 850 °C and FA-NaF coordination ratio of 1:0.5.

9 July 2025 in Sustainability
Verified
Journal Article
Open access
PDF file
WLWen Liu
Wen Liu
YHYong Huang
Yong Huang
YHYulin He
Yulin He
WHWei Hanyu
Wei Hanyu
RBRuyun Bai
Ruyun Bai
SLSining Li
Sining Li
The inherent limitations of ordinary cement mortar—characterized by its high brittleness and low flexibility—result in a diminished load-bearing capacity, predisposing concrete pavements to cracking. A novel approach has been proposed to enhance material performance by incorporating emulsified asphalt and latex into ordinary cement mortar, aiming to improve the flexibility and durability of concrete pavements effectively. To further validate the feasibility of this proposed approach, a series of comprehensive experimental investigations were conducted, with corresponding conclusions detailed herein. As outlined below, the flexibility properties of the modified cement mortar were systematically evaluated at curing durations of 3, 7, and 28 days. The ratio of flexural to compressive strength can be increased by up to 38.9% at 8% emulsified asphalt content at the age of 28 days, and by up to 50% at 8% latex content. The mechanism of emulsified asphalt and latex-modified cement mortar was systematically investigated using a suite of analytical techniques: X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, thermogravimetric analysis (TG-DTG), X-ray photoelectron spectroscopy (XPS), and scanning electron microscopy (SEM). Through comprehensive analyses of microscopic morphology, hydration products, and elemental distribution, the enhancement in cement mortar toughness can be attributed to two primary mechanisms. First, Ca2+ ions combine with the carbonyl groups of emulsified asphalt to form a flexible film structure during cement hydration, thereby reducing the formation of brittle hydrates. Second, active functional groups in latex form a three-dimensional network, regulating internal expansion-contraction tension in the modified mortar and extending its service life.