Abhendra Kumar Singh

Dr. Abhendra Kumar Singh

orcid

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 February 2022 in Ceramics International
Verified
Journal Article
Closed access
BOBrianna Ortega
Brianna Ortega
BKBrian Kitt
Brian Kitt
Abhendra Kumar SinghAbhendra Kumar Singh
Abhendra Kumar Singh
KKKaitlyn Kahle
Kaitlyn Kahle
KLKeeley Lee
Keeley Lee
ZBZach Benedict
Zach Benedict

15 March 2022 in Polymer Composites
Verified
Journal Article
Open access
ANAmir Nasirmanesh
Amir Nasirmanesh
Abhendra Kumar SinghAbhendra Kumar Singh
Abhendra Kumar Singh
DVDaniel Villaflor
Daniel Villaflor
BBBenjamin Blandford
Benjamin Blandford
The effects of embedding a midplane carbon nanotube (CNT) sheet on the impact damage resistance, tensile strength and propensity for interlaminar shear failure in a carbon fiber reinforced polymer matrix composite is experimentally evaluated. External and internal damage in the impacted composite laminates were characterized via surface profilometry and ultrasonic C‐scan, respectively. The external dent areas and dent depths were greater for impacted laminates without the CNT sheet interleave, while the planar internal damage areas were greater for the impacted laminates with the CNT sheet. Destructive evaluation of the impacted laminates showed significant delaminations and matrix cracks in the vicinity of the midplane for the laminates with the CNT sheet, while damage was more distributed through the thickness in the non‐CNT sheet ones. While a single CNT sheet interleave did not significantly affect the tensile strength of the laminate, residual strength after impact and the corresponding strain to failure was higher because of the CNT sheet interleave. The propensity for interlaminar shear failure was greater for laminates without the CNT sheet than those with the CNT sheet.

13 February 2017 in Journal of Composite Materials
Verified
Journal Article
Closed access
Abhendra Kumar SinghAbhendra Kumar Singh
Abhendra Kumar Singh
VSVolodymyr Sabelkin
Volodymyr Sabelkin
SMShankar Mall
Shankar Mall
Tension–tension fatigue tests in a combustion environment were performed on double-edge notched oxide/oxide ceramic matrix composite specimens. The composite, designated as N720/A, constituted woven 0°/90° Nextel™720 fibers in alumina matrix. Monotonic tensile and cyclic loads at a frequency of 1 Hz and a stress ratio of 0.05 were applied on the specimens in a combustion environment. The maximum specimen temperature due to combustion flame impingement in the notch region was 1250 ± 50℃. A stiffness reduction of less than 10% evaluated for the run-out specimens showed the harsh combustion environment had a minimal effect on specimen degradation. The residual strength was evaluated to be ∼75%–85% the strength of non-fatigued (virgin) double-edge notch specimens in room temperature. The monotonic tensile strength and the fatigue limit for 90,000 cycles (run-out) were found to be ∼40 MPa less in the combustion environment when compared to published results for 1200℃ laboratory air environment. The damage mechanisms were also the same in the two environments. Finite element analyses showed that the reduction in strength and fatigue limit in the combustion environment (as compared to the laboratory air environment) was due to the presence of thermal gradient stresses because of non-uniform specimen temperature distribution.

20 August 2017 in International Journal of Applied Ceramic Technology
Verified
Journal Article
Closed access
PDF file
Abhendra Kumar SinghAbhendra Kumar Singh
Abhendra Kumar Singh
SMShankar Mall
Shankar Mall

9 August 2017 in Advances in Applied Ceramics: Structural, Functional and Bioceramics
Verified
Journal Article
Closed access
Abhendra Kumar SinghAbhendra Kumar Singh
Abhendra Kumar Singh
VSVolodymyr Sabelkin
Volodymyr Sabelkin
SMShankar Mall
Shankar Mall
Creep-rupture tests were performed in the combustion environment on double-edge notch and centre hole oxide/oxide ceramic matrix composite specimens. The specimens were exposed to the maximum temperature of 1250 ± 50°C in the notch region where the combustion flame directly impinged. Specimens were loaded to the desired creep load levels and the loads were sustained till either the specimens ruptured or a run-out time of 25 h was achieved. Optical and scanning electron microscopes were used to characterise specimen damage. The test results were compared to its counterparts in 1200°C (isothermal) laboratory air environment. At a given creep life, the applied creep stress for both the notch types was generally lower in the combustion environment than the laboratory air environment. Finite element simulations attributed lower applied creep stress in the combustion environment to the presence of thermal gradient stresses, which were not present in the isothermal laboratory air environment.

31 July 2022 in Ceramics International
Verified
Journal Article
Closed access
VSV.N.B. Prasad Sodisetty
V.N.B. Prasad Sodisetty
Abhendra Kumar SinghAbhendra Kumar Singh
Abhendra Kumar Singh
HJHannah James
Hannah James
KLKeeley Lee
Keeley Lee
ZBZach Benedict
Zach Benedict