The review is devoted to the analysis of the compositional disordering potential of the crystal matrix of a scintillator to improve its scintillation parameters. Technological capabilities to complicate crystal matrices both in anionic and cationic sublattices of a variety of compounds are examined. The effects of the disorder at nano-level on the landscape at the bottom of the conduction band, which is adjacent to the band gap, have been discussed. The ways to control the composition of polycationic compounds when creating precursors, the role of disorder in the anionic sublattice in alkali halide compounds, a positive role of Gd based matrices on scintillation properties, and the control of the heterovalent state of the activator by creation of disorder in silicates have been considered as well. The benefits of introducing a 3D printing method, which is prospective for the engineering and production of scintillators at the nanoscale level, have been manifested.

Luminescent and scintillation ceramic materials with complex shapes, which can be created by stereolithography 3D printing, are of interest for special phosphor and detector applications. Starting powders for such ceramics may possess UV absorption bands; therefore, it is important to study the possible influence of the powders’ luminescent properties on the printing process. This paper deals with complex garnet oxides, Y₃Al₅O₁₂ and Gd₃Al₂Ga₃O₁₂—well-known hosts for luminescent materials. The photopolymerization rates of slurries based on the luminescent powders produced by various chemical routes are studied, as well as available printing regimes. The slurries containing Ce-doped powders with a broad absorption band in UV have significantly lower photopolymerization rates compared to the undoped ones; a high Ce doping virtually hinders printing with layers thicker than 25–50 μm. Furthermore, the choice of powder synthesis method is shown to influence the printing process. Slurries with Tb-doped powder, with absorption lines at shorter wavelengths, have good photopolymerization activity, close to that of the undoped powder, and can be printed with layer thicknesses of 25–100 μm.

GYAGG:Tb (Ce) scintillators have been confirmed to be promising sources of light emission when excited by an intense 150 keV electron beam. The saturation of the scintillation yield under such excitation conditions has been studied. To explain the results obtained, a model that considers the Auger quenching mechanism was used. The Ce-doped material did not show saturation, whereas a moderate 30% drop of the yield was measured in the Tb-doped sample at the highest excitation beam intensity ~1 A/cm². This put forward a way to exploit the Tb-doped scintillator for indirect β-voltaic batteries.

Dense and transparent ceramic samples of a (Gd,Y)₃Al₂Ga₃O₁₂:Ce scintillator were obtained by using stereolithography-based Digital Light Processing (DLP) 3D printing for compacting, subsequent burnout, and pressureless sintering. The effects of stoichiometric deviations and green body compaction methods (uniaxial pressing versus DLP 3D printing) on the optical, luminescent, and scintillation properties of ceramics were analyzed. An excess of Y and Gd in the composition led to an increase in transmittance and to the acceleration of the scintillation kinetics. Moreover, transparent ceramics made of 3D-printed green bodies were found to be superior in light yield to the samples, which were prepared from the same powders and densified by uniaxial pressing.

A method to create compositionally disordered compounds with a high number of cations in the matrices, that utilize the cubic spatial symmetry of the garnet-type crystalline systems is demonstrated. Mixtures of the garnet-type powdered materials solely doped with Ce were used to create atomic compositions of high complexity. Several mixed systems, namely Gd₃Al₂Ga₃O₁₂/(Gd,Y)₃Al₂Ga₃O₁₂, Y₃Al₅O₁₂/Gd₃Al₂Ga₃O₁₂, and Y₃Al₅O₁₂/Y₃Al₂Ga₃O₁₂ were annealed, compacted and sintered in air. The materials were evaluated for structural, luminescence, and scintillation properties. It was demonstrated that the properties of the resulting ceramics are a little dependent on the granularity of powders when the median particle size is below ~5 μm.