This paper presents a numerical study of a multilayer composite panel impacted by an AP (Armor Piercing) 14.5×114 mm B32 projectile. The composite consists of alternating layers of hard ceramic and a ductile aluminum alloy. While the alloy layer consists of typical plate, ceramics confront projectiles in the form of ceramic pyramids. The studied models are compared with a reference structure, which is a standard double layer panel. The problem has been solved with the usage of modeling and simulation methods as well as a finite elements method implemented in LS-DYNA software. Space discretization for each option was built with three dimensional elements ensuring satisfying accuracy of the calculations. For material behavior simulation, specific models including the influence of the strain rate and temperature changes were considered. A steel projectile and aluminum plate material were described by the Johnson-Cook model and a ceramic target by the Johnson-Holmquist model. The obtained results indicate that examined structures can be utilized as a lightweight ballistic armor in certain conditions. However, panels consisting of sets of ceramic prisms are a little easier to penetrate. Despite this fact, a ceramic layer is much less susceptible to overall destruction, making it more applicable for the armor usage. What is most important in this study is that significant projectile trajectory deviation is detected, depending on the impact point. Such an effect may be utilized in solutions, where a target is situated relatively far from an armor.

Hydraulic fracturing of rocks boosts the production rate by increasing the fracture-face surface area through the use of a pressurized liquid. Complex stress distribution and magnitude are the main factors that hinder the use of information gathered from in situ hydraulic fracturing in other locations. Laboratory tests are a good method for precisely determining the characteristics of these processes. One of the most important parameters is breakdown pressure, defined as the wellbore pressure necessary to induce a hydraulic fracture. Therefore, the main purpose of this investigation is to verify fracture resistance of rock samples fractured with the assistance of the most popular industry fluids. The experiments were carried out using a stand designed specifically for laboratory hydraulic fracturing. Repeatable results with a relative error within the range of 6-11% prove that the experimental methodology was correct. Moreover, the obtained results show that fracturing pressure depends significantly on fluid type. In the case of a water test, the fracturing pressure was 7.1±0.4MPa. A similar result was achieved for slickwater, 7.5±0.7MPa; however, a much lower value (4.7±0.5MPa) was registered in the case of carbon dioxide.

This paper presents a 2D numerical study of v-shape deflectors subjected to high explosive charge detonation. The literature provides many papers concerning the appropriate geometry of blast protection deflectors. Such structures require a relatively high distance between the ground and the vehicle chassis. In most cases, the placement of a deflector is not possible or it cannot cover the whole area under a chassis. An interesting question that arises is to what extent a set of small deflectors would be able to mitigate blast effects. The content of this paper constitutes an answer to this question. Three analyses were conducted: (1) multiplication of triangle components, (2) effect of deflector size, and (3) geometry-induced shock dynamics. The problem was solved with the use of modelling and simulation methods, in particular, CFD-FEM implemented in the LS-DYNA code. It was considered a plain issue in computational fluid dynamics, where space discretization for each option was built with two-dimensional elements to ensure efficient calculations. Deflectors were described using a rigid wall boundary condition, and an adequate simplified detonation model was assumed. The primary measure of the results was reaction force history, with momentum transfer and pressure distribution maps considered supplementary. The studies performed showed that both minimizing the v-shape deflector size and surrounding it with adjacent structures had a negative impact on its blast mitigation effectiveness. However, for each multi-v-shape deflector, some improvement was present, and, therefore, in situations where the installation of a typical protector is not possible due to dimensional requirements, it may offer a compromise solution.

The paper presents a numerical study of a double layer composite panels impacted by a AP (Armor Piercing) 51WC projectile. The standard panel is built with aluminum and Al2O3 ceramic continuum layers while the studied model consists of the same aluminum plate but the front one is built with a set of hexagonal ceramic bars. The bar width and the impact position influence on the ballistic resistance are analyzed and compared with the reference solution. The problem has been solved with the usage of the modeling and simulation methods as well as finite elements method implemented in LS-DYNA software. Space discretization for each option was built by three dimension elements guarantying satisfying accuracy of the calculations. For material behavior simulation specific models including the influence of the strain rate and temperature changes were considered. Projectile Tungsten Curbide and aluminum plate material were described by Johnson-Cook model and ceramic target by Johnson-Holmquist model. In the studied panels the area surrounding back edges was supported by a rigid wall. The obtained results show interesting properties of the examined structures considering their ballistic resistance. All tests has given clear results about ballistic protection panel response under WC projectile impact. Panels consisting of sets of hexagonal ceramic bars are slightly easier to penetrate, reference model is stronger by 19% for smaller bars and by only 7% for bigger rods. Despite this fact, the ceramic layer is much less susceptible to overall destruction what makes it more applicable for the armor usage. Furthermore, little influence of the projectile impact point and consequently a part of the bar which is first destroyed is proved.