Satoru Takada

Dr. Satoru Takada


Research Focus & Metrics

Academic Career Length

20Years (2007-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
2 October 2009 in International Journal of Biometeorology
Verified
Journal Article
Closed access
PDF file
AMAbdul Munir
Abdul Munir
STSatoru Takada
Satoru Takada
TMTakayuki Matsushita
Takayuki Matsushita
HKHiroko Kubo
Hiroko Kubo

22 March 2024 in Journal of Building Physics
Verified
Journal Article
Closed access
KFKazuma Fukui
Kazuma Fukui
STSatoru Takada
Satoru Takada
When the water content of a porous material is high, air entrapped in the pore space is expected to affect water transfer through the pores. To understand the effects of air entrapment on water transfer in porous building materials in the high-water-saturation region, we examined the water transfer characteristics corresponding to significantly small air entrapment effects. First, we conducted two sets of water uptake experiments. In the first experiment, using three building materials, the time evolution of the amount of water absorption was measured at a low air pressure near vacuum (several kPa). In the second experiment, the water content profile during water uptake was measured using the gamma-ray attenuation method. The experimental results showed that low air pressure accelerated the water uptake by the brick and aerated concrete specimens, whereas water uptake by the calcium silicate board specimens was not significantly affected. These differences among materials were analyzed from a pore structure viewpoint. Moreover, gamma-ray attenuation measurements confirmed that the obtained water content profile was qualitatively similar at atmospheric and low air pressures, although the low air pressure increased both the water content of the material after capillary absorption and the wetting front propagation rate. Finally, simultaneous water and air transfer calculations based on the air and liquid water balance in a material reproduced the measured water absorption rates well, confirming that air entrapment and pressure development in the pores can significantly reduce the rate of water uptake and water content after capillary absorption. The calculation results also indicated that the air pressure in a material did not significantly increase at early water uptake stages where local water content was not high, which supported the general assumption that treating the liquid-water transfer in porous building materials as a one-component flow is valid in most cases.

1 February 2013 in Journal of Building Physics
Verified
Journal Article
Closed access
PDF file
STSatoru Takada
Satoru Takada
TMTakayuki Matsushita
Takayuki Matsushita
Occupants of low-humidity environments often complain of a sensation of dryness. According to the results of a questionnaire administered to 1000 Japanese office workers, 70% of that population experiences dryness during dry seasons. It is therefore important to clarify the environmental conditions that cause discomfort due to dryness and control the indoor environmental conditions to avoid such discomfort. For the purpose, this study aims at creating a numerical model to predict the sensation of dryness under certain environmental conditions. Since one of the causes of dryness would be the high evaporation rates from the body part where dryness is perceived, the modeling of moisture evaporation from the surface of skin, eyes, and airway was studied in this article, using the thermal model of human body. At the same time, the evaporation rates from the skin surface, eyes, and airway of a human were calculated for various air temperatures and humidity levels. It was shown quantitatively from the calculated results that the air temperature as well as the vapor pressure influences the evaporation rate because the air temperature thermally influences the temperature of the surface where evaporation occurs (skin, eyes, and throat).

20 October 2021 in Journal of Building Physics
Verified
Journal Article
Closed access
PDF file
HYHiroaki Yamamoto
Hiroaki Yamamoto
STSatoru Takada
Satoru Takada
Depending on the data source used, the material hygrothermal properties that are used in the numerical analysis of simultaneous heat and moisture transfer will not be consistent. Differences in measurement methods and the individuality of specimens account for this. It is necessary to choose values from these different physical property sets to conduct a numerical calculation, which can cause the calculated results to differ. The subsequent range of variation in the calculated results should be quantitatively evaluated. In this study, the physical properties of several types of porous building materials were first gathered from four databases. The data were then categorized based on the kind of material and compared in terms of each physical property (density, porosity, specific heat, moisture capacity, thermal conductivity, and vapor permeability). The density, porosity, and specific heat varied by 10% on average, and the moisture capacity, thermal conductivity, and vapor permeability varied by 20% or more for all types of materials. In particular, the vapor permeability of plywood and moisture capacity of gypsum board differed by 50%. The influence that these physical property value variations had on hygrothermal calculation results was then quantitatively demonstrated for moisture and heat flow rate under a step change in the relative humidity or temperature of indoor air for a single layer wall. The moisture and heat flow rate into a single layer wall fluctuated by approximately 10%–40% due to differences in the vapor permeability and moisture capacity of the materials. For all types of materials, moisture was transferred more slowly than heat. Therefore, differences in moisture property values, such as vapor permeability and moisture capacity, influenced the results more significantly. Moreover, the moisture flow was accompanied by a phase change. The differences in moisture property values thus affected the heat flow.

1 October 2007 in Journal of Building Physics
Verified
Journal Article
Closed access
STSatoru Takada
Satoru Takada
SHS. Hokoi
S. Hokoi
MKM.K. Kumaran
M.K. Kumaran
In order to design an efficient air-conditioning system, the specifics of the transient thermal and physiological responses of a human body to the hygrothermal environment should be taken into account. This response will strongly depend on the behavior of heat and moisture transport, and moisture accumulation in the clothing, especially when sweat exists in and around the clothing. As a basic information on this problem, a model of the moisture transfer in cloth is necessary. In this article, a model of the liquid moisture movement in clothing under gravity is developed and applied, based on a diffusion model. Firstly, the moisture diffusivity is determined from the investigation of the moisture absorption process in the horizontal direction where gravity has no influence on the moisture movement. Secondly with the use of the moisture diffusivity thus determined, a moisture absorption process in the upward direction against gravity is investigated. The validity of the parameter related to the gravity effect is examined by comparing the results of numerical calculations with the experimental results obtained from the gamma-ray method. Since the two agree generally well, the parameters namely liquid moisture diffusivity and sorption isotherm derived here for a sample of broadcloth are considered reliable.