Aron Ringel

Mr. Aron Ringel

orcid

Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
9 October 2023 in Metals
Verified
Journal Article
Open access
PDF file
LBLukas Bruckmeier
Lukas Bruckmeier
ARAron Ringel
Aron Ringel
UVU. Vroomen
U. Vroomen
DBDavid Bailly
David Bailly
ABAndreas Bührig-Polaczek
Andreas Bührig-Polaczek
Reducing the weight of parts through lightweight designs impacts CO2 emissions, especially in the automotive and transportation sectors, which have significant fuel and electric energy consumption. Using multi-material design approaches, specific material properties can be combined to achieve effective lightweighting. Commonly used metals include aluminum, which is known for its high specific strength, and steel, which is valued for its strength and structural integrity. However, joining aluminum and steel presents challenges given their different thermophysical properties and the potential formation of brittle intermetallic phases, making common joining techniques like fusion welding unsuitable. In this study, a hybrid casting process for the production of a complex workpiece from dissimilar materials was investigated. Aluminum was die-cast around a steel sheet insert. Surface structures with undercuts on the steel sheet were applied through modified cold rolling, allowing molten aluminum to flow into the channels and interlock during solidification. It was found that elevated temperatures of the melt and tool were beneficial for the interlocking, resulting in a 30% increase in compound strength. Furthermore, a reduction in both the piston position at the changeover point, between the pre-filling and cavity filling, and the melt velocity at the gate reduced the compound’s strength by 41% and 30%. Up- and downstream processes did not show any significant influence on the conducted experiments. Based on this, two main detrimental effects were observed: pre-solidification of the aluminum melt and gas entrapment.

9 November 2023 in International Journal of Material Forming
Verified
Journal Article
Open access
PDF file
ARAron Ringel
Aron Ringel
GHGerhard Kurt Peter Hirt
Gerhard Kurt Peter Hirt
Due to the current changes in mobility, lightweight design concepts continue to be of particular interest to the automotive industry. One form is the multi-material design, in which the advantageous properties of different materials are combined in one component. In this work, a component made of a steel sheet with stiffening structures of cast aluminum is considered. The joint is created by channel structures with undercuts on the surface of the steel sheet, into which the molten aluminum can flow. After solidification, an interlocking connection is created. The aim of this work is to investigate the influence of a bending operation on the surface structure before the die casting process. Numerical simulations and experimental validations were performed with different bending angles and radii as well as orientations between the channel structure and the punch. The results show that the undercuts on the outer radius are reduced by up to 75% by the bending operation, thus weakening the resulting joint. On the inner radius, the channel opening width narrows by up to 73% and can thus impede the filling with the melt.

16 August 2024 in Machines
Verified
Journal Article
Open access
PDF file
ARAron Ringel
Aron Ringel
SSSindokht Shayan
Sindokht Shayan
DBDavid Bailly
David Bailly
Weight reduction strategies are essential for the transportation sector to reduce greenhouse gas emissions or extend the range of electric vehicles. In the field of lightweight assembly strategies, multi-material design offers great potential. Joining materials typically used in the automotive sector, such as aluminum and steel, brings challenges as conventional processes such as fusion welding are unsuitable. Therefore, new technologies can extend the design options. In previous studies, a mechanical interlocking between cold-rolled surface structures with undercuts on a steel sheet and die-cast aluminum was presented. This method has now been extended to double-sided structures for more complex applications with a joint on both sheet surfaces. Numerical simulations and validation experiments were performed to investigate the manufacturing of the double-sided structures. Furthermore, the influence of the alignment of the upper and lower structures in relation to each other on the resulting structural geometry and the rolling forces were analyzed. More advantageous geometric parameters, e.g., 24% larger undercuts, and approx. 24.1% lower forming forces at 20% height reduction were observed for a shifted alignment. However, significantly higher wear of the structured rollers occurred in the corresponding experiments.

15 May 2024 in Materials Research Proceedings
Verified
Conference Paper
Open access
PDF file
ARAron Ringel
Aron Ringel
DBD. Bailly
D. Bailly
-Influence of cold rolled surface structures with undercuts for interlocking joints on bending processes RINGEL Aron, BAILLY David [button link="https://www

15 April 2026 in Materials Science Forum
Verified
Journal Article
Open access
PDF file
ARAron Ringel
Aron Ringel
ADAhmet Zahid Demirezen
Ahmet Zahid Demirezen
JHJulika Hoyer
Julika Hoyer
DBDavid Bailly
David Bailly
SKSimon Kammerloher
Simon Kammerloher
JLJunhe Lian
Junhe Lian
Multi-material components that consist of copper and aluminum enable the combination of advantageous mechanical, thermal, and electrical properties at competitive cost. While roll bonding is an efficient-solid state joining technique, its implementation requires fully processed, cold-rolled strip material from two process routes. Continuous compound casting in contrast offers a more efficient approach by combining aluminum and copper during casting, followed by flat rolling in a single process route. However, the differences in flow stress between the metals can cause non-uniform elongation and therefore significant shear stresses at the interface during rolling. These stresses may lead to a delamination of the compound if process conditions are not well controlled. This study investigates whether a geometrically structured interface, introduced during compound casting, can contribute to withstanding interfacial shear stresses through mechanical interlocking. In finite element simulations varying process parameters including height reduction, initial temperature, rolling speed ratio, and pass schedule were examined. Results show that a structured interface can effectively resist shear stresses at the copper-aluminum boundary, thereby improving joint stability during deformation. Furthermore, the strain distribution as well as the fluctuation of the shear stresses can be controlled by the process parameters. The findings indicate that the mechanical interlocking by a geometric interface combined with optimized process parameters can enhance the rolling of compound-cast copper-aluminum composites.

1 September 2025 in Journal of Physics: Conference Series
Verified
Conference Paper
Open access
ARAron Ringel
Aron Ringel
OEOliver Edwin
Oliver Edwin
ESEmad Scharifi
Emad Scharifi
DBDavid Bailly
David Bailly
In sandwich structures, a corrugated core layer is often joined to cover layers along a seam. The lightweight construction potential and high rigidity make such components attractive for a wide range of applications, e.g. for battery housings of electric vehicles. One multi-material approach uses a layer of steel with higher strength for impact protection and an aluminium sheet with low weight and high thermal conductivity for cooling. However, joining of dissimilar materials presents challenges. Metallurgical bonding methods, such as fusion welding, can result in brittle intermetallic phases at the interface. Fasteners like rivets add extra weight and create localized joints only, while adhesives typically exhibit lower strength and adverse aging effects. To overcome these drawbacks, this study proposes a process in which two materials are mechanically joined along a longitudinal seam by cold rolling. First, surface structures with undercuts are rolled into a stronger base material. Secondly, softer material is rolled into the structures. A 2D forming simulation is created to illustrate the rolling of Al99.5 sheets into surface structures on DC04 sheets and experimentally validated. To explore the limits with regard to the strength ratio of the materials two aluminium grades with higher yield strength (AlMg3, AlMg4.5) are selected for simulation and validation experiments. The results indicate that a yield strength ratio exceeding 1.4 is essential for successful joining by cold rolling. At lower ratios, the aluminium flow into the steel’s surface structure is insufficient.