Paulina Kaszubska

Ms. Paulina Kaszubska

orcid

Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
11 March 2025 in Materials
Verified
Journal Article
Open access
PDF file
Jacek SzafranJacek Szafran
Jacek Szafran
KJKlaudia Juszczyk-Andraszyk
Klaudia Juszczyk-Andraszyk
PKPaulina Kaszubska
Paulina Kaszubska
This paper presents an analysis of the effectiveness of the existing reinforcement of steel lattice tower legs made of L-sections by expanding to closely spaced built-up members. Due to the significant differences between the standard assumptions and the existing reinforcement, numerical analyses based on the component-based finite element method (CBFEM) were used to estimate the capacity of the existing structure’s tower legs. Geometrically and materially nonlinear stress analysis and linear buckling analysis were performed. The obtained results (stress distribution maps, buckling forms, and corresponding critical forces) were used to modify the geometric parameters of the section of the analyzed tower legs in order to adapt the standard formulas in the calculation procedure. In the analyzed case, distance of the connections between the branches exceeded that indicated in EN 1993-1-1:2005 for the condition concerning the possibility of ignoring the deformation susceptibility in the calculation process. However, it did not result in the separate operation of each branch of the section. Thus, in the case of the analyzed reinforcement, it is possible to neglect the form susceptibility when calculating the buckling resistance of the element. The buckling capacity of the reinforced legs of the tower and the compression capacity of the section of the analyzed structure were calculated according to the method that took into account the results of the numerical analyses. These values are about 35–48% and 30–39% higher, respectively, than the capacity of the unreinforced angle calculated according to EN 1993-1-1:2005 and EN 1993-1-8:2006 standards. Thus, it may be possible to avoid costly and labor-intensive retrofitting of the existing reinforcement to meet the standard requirements. A key issue, and one that is particularly important in light of the lack of standard guidelines aimed at designing reinforcements for telecommunications structures, seems to be the performance of full-scale experimental tests.

17 December 2025 in Materials
Verified
Journal Article
Open access
PDF file
Jacek SzafranJacek Szafran
Jacek Szafran
PŚPaulina Świątkiewicz
Paulina Świątkiewicz
PKPaulina Kaszubska
Paulina Kaszubska
In the context of growing environmental consciousness, the contemporary construction industry is placing significant emphasis on prolonging the functional lifespan of existing infrastructure. In the event of a modification in the utilisation of a building, an augmentation in the loads transferred to individual elements, or a deterioration in the condition of the structure due to wear and tear, it is often necessary to implement measures for structural reinforcement. The present paper sets out an analysis of the effectiveness of strengthening a steel column manufactured from SHS120×120×5. It was posited that four distinct reinforcement variants could be achieved by the implementation of additional stiffening elements through the process of welding. The efficiency analysis was conducted employing two distinct methodologies. The geometrical imperfection method is employed using the IDEAStatiCa Member 25.0.4 software, whilst the analytical method is implemented through the use of guidelines presented in the literature. It was demonstrated that all of the proposed solutions were capable of meeting the required column capacity when the loads were increased. A comparison was made between the values of the critical forces and the members’ stresses, determined by the selected methods. A substantial discrepancy was identified between the critical force values derived from linear buckling analysis and those calculated using elastic Euler theory. The following discourse herein delineates the primary advantages and limitations of the two aforementioned methods.


7 August 2024 in Materials
Verified
Journal Article
Open access
PDF file
AWArtur Wirowski
Artur Wirowski
EKEwelina Kubacka
Ewelina Kubacka
PKPaulina Kaszubska
Paulina Kaszubska
WWWeronika Walisiak
Weronika Walisiak
In this study, a numerical dynamic analysis of ceiling raster panels was performed. The analysis was conducted on panels designed with inspiration from bionics. The purpose of the analysis was to enable optimisation of the location of the holes in the designed slabs in order to achieve the preferred dynamic properties, including the natural frequencies of the slabs and an appropriate airflow to avoid the occurrence of resonance. Three different types of panels were used and a total of fifteen panels were designed in terms of their geometry, with circular, elliptical, and hexagonal perforations, made of different materials: polypropylene PP, wood, and aluminium. Then, using the finite element method and ANSYS 2023 R1 software, the airflow over the ceiling panels and their natural frequencies and vibration modes were analysed. The analysis took into account not only the shape of the openings, but also their percentage area relative to the total panel area and different airflow velocities. In addition, the results were compared in an analytical way with those obtained for a solid slab. The results obtained include findings on the mode shapes and values of the vibration frequencies of the plates, air pressure maps, histograms, and plots of the pressure dependence on the surface area of the plate openings.

15 July 2024 in BUILDER
Verified
Journal Article
Closed access
AWArtur Wirowski
Artur Wirowski
EKEwelina Kubacka
Ewelina Kubacka
ZFZuzanna Frąckowicz
Zuzanna Frąckowicz
PKPaulina Kaszubska
Paulina Kaszubska
W pracy przedstawiono ideę, zgodnie z którąpowstanie nowoczesnego budynku mieszkalnegozapewniającego komfort użytkownikomjest efektem świadomego współdziałaniacałego zespołu specjalistów, począwszyod fazy projektowej, aż do oddania budynkudo użytkowania. Każdy z uczestników tegoprocesu powinien mieć świadomość, że nadrzędnymcelem nie jest wyłącznie spełnienienorm i warunków technicznych, a stworzeniepewnego sztucznego ekosystemu zwróconegona potrzeby konkretnego człowieka –użytkownika danego budynku mieszkalnego.W pracy skupiono się na wybranych aspektachkomfortu użytkownika i opisano systemy,które zyskują popularność na całymświecie i są w stanie go zapewnić, nie analizowanonatomiast jakości przestrzeni i ergonomiiw sensie architektonicznym. Zaproponowanorozwiązania, które mogą przekształcićbudynek mieszkalny w ekosystem zwróconyna człowieka. Opisano koncepcję budownictwazrównoważonego, zyskujący na popularnościnurt zwany bioniką, systemy inteligentnegozarządzania obiektem, nowoczesny systemklimatyzacyjny i wprowadzane na ryneknowe materiały. Przytoczone rozwiązaniadają możliwość zaprojektowania ekosystemu,który współgra z użytkownikiem i korzystniewpływa na to, jak człowiek czuje się w danymobiekcie.