The pulsation of bubbles and the impact load from reverse flow, generated by the evolution of semiclosed initial intermittent bubble multiphase flow during underwater launches, are crucial factors affecting launch safety. This paper employs the mixture multiphase flow model and the interphase heat and mass transfer model to simulate the interaction between the gas inside a partially enclosed cylinder and the water medium outside the cylinder, combined with simulation and piggybacking experiments, to analyze the flow process and load state. The numerical model is further utilized to study the evolution of the multiphase flow field of the semienclosed initial intermittent bubble, the pulsating load of the bubble, the impact load of the inverted water flow, and the influence of structural dimensions on the load. The results show that the initial intermittent bubble in the mouth of the cylinder experiences an expansion–contraction–expansion pulsation process, and as the migration of the interface between the phases results in significant pressure pulsation, the peak pulsation can exceed twice the pressure difference between the initial gas pressure inside the cylinder and the hydrostatic pressure at the mouth of the cylinder. At the late stage of bubble pulsation, a large amount of water with pulsating bubbles flows into the semiclosed cylinder, and the pulsation-induced velocity and gravity are used to form a high-speed inverted water flow. The interaction between the inverted water and the gas inside the cylinder generates an oscillating shock load where the maximum shock load is significantly greater than the ambient pressure load. Additionally, the effect of structural dimensions on the load state under the same intermittent conditions is examined.
To simulate the launching process of missile complex flow, movement, and constraint states, a multifield coupling model is put forward based on a computational fluid dynamics (CFD) method. In this coupled model, a CFD method is used to solve the three-dimensional compressible transient flow, and the six-degree motion of the launching platform is considered, and the virtual contact method is used to deal with the constraint states of the guideway and the slider. The active force and moment are applied to the launching platform to simulate its rolling, pitching, and heaving motions under the 5-level waves. Collision detection is carried out through the minimum clearance distance between the slider and the guideway, and the contact force is handled by a modified Herz collision model. In the problem of launching a missile from the water surface, the change characteristics of the flow field, the load response characteristics, and the relative motion laws of the missile and the launching platform during the catapulting process are investigated. The results show that the motion laws of the projectile and the launch tube in the constrained direction are the same, and the established coupling model is able to simulate the launch separation process of the missile in the constrained state. In addition, the effect of wind load on the missile ejection process is analyzed using the coupled model.
The underwater semiclosed gas–liquid multiphase flow process and load response characteristics have been introduced in our former research [Liu et al., “Numerical investigation of the multiphase flow and loading state of underwater semiclosed initial interrupted bubbles,” Phys. Fluids 36(9), 093356 (2024)]. In this paper, the formation mechanism of water hammer impact is further improved by analyzing the change of fluid state parameters at the characteristic position inside the cylinder, and then the response characteristics of the load at different initial conditions are studied, revealing the influence law of the initial conditions on the load. First, the numerical simulation model was verified with ground simulation experiments and underwater large-depth loading experiments to simulate the initial interrupted gas–liquid multiphase flow in typical states, and the load response during the evolution of the gas–liquid phase was obtained. Furthermore, the formation mechanism of bubble pulsation and water hammer impact loading is refined in combination with changes in flow parameters. Second, the mechanism of action of initial values, such as the launcher exit depth and the initial pressure difference on the load, was investigated, and the relationship between typical parameters and the load was obtained. The results show that with increasing water depth at the launcher exit, the relative pressure change caused by bubble pulsation gradually decreases, the relative pressure change caused by water hammer impact gradually increases, and the time it takes for the two loads to peak gradually decreases. With increasing initial pressure difference between the inside and outside of the cylinder, the bubble pulsation load is positively correlated with the initial pressure difference, whereas the water hammer impact load tends to increase first and then decrease. The initial pressure difference has little effect on the period of the pulsating load of the air bubble at the cylinder, but the time it takes for the water hammer impact load to peak decreases with increasing pressure difference.
23 January 2026 in Journal of Computational Physics