Lignocellulose biorefining is a promising technology for the sustainable production of chemicals and biopolymers. Usually, when one component is focused on, the chemical nature and yield of the others are compromised. Thus, one of the bottlenecks in biomass biorefining is harnessing the maximum value from all of the lignocellulosic components. Here, we describe a mild stepwise process in a flow-through setup leading to separate flow-out streams containing cinnamic acid derivatives, glucose, xylose, and lignin as the main components from different herbaceous sources. The proposed process shows that minimal degradation of the individual components and conservation of their natural structure are possible. Under optimized conditions, the following fractions are produced from wheat straw based on their respective contents in the feed by the ALkaline ACid ENzyme process: (i) 78% ferulic acid from a mild ALkali step, (ii) 51% monomeric xylose free of fermentation inhibitors by mild ACidic treatment, (iii) 82% glucose from ENzymatic degradation of cellulose, and (iv) 55% native-like lignin. The benefits of using the flow-through setup are demonstrated. The retention of the lignin aryl ether structure was confirmed by HSQC NMR, and this allowed monomers to form from hydrogenolysis. More importantly, the crude xylose-rich fraction was shown to be suitable for producing polyhydroxybutyrate bioplastics. The direct use of the xylose-rich fraction by means of the thermophilic bacteria Schlegelella thermodepolymerans matched 91% of the PHA produced with commercial pure xylose, achieving 138.6 mgPHA/gxylose. Overall, the ALACEN fractionation method allows for a holistic valorization of the principal components of herbaceous biomasses.
6 February 2025 in International Journal of Biological Macromolecules
In recent years the number of non-Acetobacteraceae strains shown to produce nanofibrillar cellulose at the levels of the known Acetobacteraceae producers has increased considerably. The Ancylobacter sp. STN1B isolate capable of cellulose production from naphthalene has previously been described. In this study, Ancylobacter sp. STN1A, a spontaneous STN1B mutant able to produce 1.7 to 9.7 times higher levels of cellulose, has been isolated. The STN1A genome showed a 62 kb deletion encompassing a modified rpf quorum sensing signalling system that included a diguanylate cyclase-phosphodiesterase gene. A knock-out mutant of STN1B rpfC sensor kinase gene produced similarly high cellulose levels than STN1A. This confirmed that the overproducing phenotype resulted from the loss of the rpf system, which resulted in three-time higher c-di-GMP levels. The strains were able to grow on several carbon sources and produce cellulose with properties similar to those of K. xylinus processed similarly, as determined using ATR-FTIR, CP/MAS, 13C NMR, XRD, TGA and SEM, although with higher thermal resistance and water holding capacity. Production was higher under static conditions, rendering 2.5 g/L with glycerol. Interestingly, in this strain cellulose is synthesized from a type-III bcs cluster, which lacks BcsC, BcsD and BcsH sub-units. This first thorough characterization of cellulose produced from a type III cellulose synthesis complex reveals its excellent properties.
Copper nanoparticles offer a cost-effective and sustainable alternative to silver-based materials for conductive inks in printed and flexible electronics. However, their practical application is often hindered by the need for inert atmospheres and environmentally hazardous reducing agents, but most critically by their rapid postsynthesis oxidation. In this work, we report a green, scalable synthesis of oxidation-resistant metallic Cu nanoparticles via a microwave-assisted polyol method using sodium hypophosphite as a nontoxic reducing agent and lignin as a capping and stabilizing agent. Nanoparticle formation occurs during a final microwave irradiation step as short as 5 min, following a brief homogenization stage, resulting in moderately polydisperse particles with average diameters around 150 nm and without the need for an inert atmosphere. The lignin coating significantly enhances the stability of the particles, maintaining their metallic state for over 120 days in ethanol and 60 days in air. Structural and compositional analyses confirm the effectiveness of lignin in preventing surface oxidation, while electrical conductivity tests show promising values (up to 3.83 × 106 S/m, corresponding to a resistivity of 26.1 μΩ·cm), outperforming commercial references. These results demonstrate the potential of lignin-stabilized copper nanoparticles as eco-friendly conductive fillers for next-generation green and flexible electronics.