Porous biomaterials that simultaneously mimic the topological, mechanical, and mass transport properties of bone are in great demand but are rarely found in the literature. In this study, we rationally designed and additively manufactured (AM) porous metallic biomaterials based on four different types of triply periodic minimal surfaces (TPMS) that mimic the properties of bone to an unprecedented level of multi-physics detail. Sixteen different types of porous biomaterials were rationally designed and fabricated using selective laser melting (SLM) from a titanium alloy (Ti-6Al-4V). The topology, quasi-static mechanical properties, fatigue resistance, and permeability of the developed biomaterials were then characterized. In terms of topology, the biomaterials resembled the morphological properties of trabecular bone including mean surface curvatures close to zero. The biomaterials showed a favorable but rare combination of relatively low elastic properties in the range of those observed for trabecular bone and high yield strengths exceeding those reported for cortical bone. This combination allows for simultaneously avoiding stress shielding, while providing ample mechanical support for bone tissue regeneration and osseointegration. Furthermore, as opposed to other AM porous biomaterials developed to date for which the fatigue endurance limit has been found to be ≈20% of their yield (or plateau) stress, some of the biomaterials developed in the current study show extremely high fatigue resistance with endurance limits up to 60% of their yield stress. It was also found that the permeability values measured for the developed biomaterials were in the range of values reported for trabecular bone. In summary, the developed porous metallic biomaterials based on TPMS mimic the topological, mechanical, and physical properties of trabecular bone to a great degree. These properties make them potential candidates to be applied as parts of orthopedic implants and/or as bone-substituting biomaterials. Bone-substituting biomaterials aim to mimic bone properties. Although mimicking some of bone properties is feasible, biomaterials that could simultaneously mimic all or most of the relevant bone properties are rare. We used rational design and additive manufacturing to develop porous metallic biomaterials that exhibit an interesting combination of topological, mechanical, and mass transport properties. The topology of the developed biomaterials resembles that of trabecular bone including a mean curvature close to zero. Moreover, the developed biomaterials show an unusual combination of low elastic modulus to avoid stress shielding and high strength to provide mechanical support. The fatigue resistance of the developed biomaterials is also exceptionally high, while their permeability is in the range of values reported for bone.

Research from JAMA — Platelet-Rich Plasma Injection for Chronic Achilles Tendinopathy — A Randomized Controlled Trial

Objective To determine the association between cam impingement, which is hip incongruity by a non-spherical femoral head and development of osteoarthritis. Methods A nationwide prospective cohort study of 1002 early symptomatic osteoarthritis patients (CHECK), of which standardised anteroposterior pelvic radiographs were obtained at baseline and at 2 and 5 years follow-up. Asphericity of the femoral head was measured by the α angle. Clinically, decreased internal hip rotation (≤20°) is suggestive of cam impingement. The strength of association between those parameters at baseline and development of incident osteoarthritis (K&L grade 2) or end-stage osteoarthritis (K&L grades 3, 4, or total hip replacement) within 5 years was expressed in OR using generalised estimating equations. Results At baseline, 76% of the included hips had no radiographic signs of osteoarthritis and 24% doubtful osteoarthritis. Within 5 years, 2.76% developed end-stage osteoarthritis. A moderate (α angle >60°) and severe (α angle >83°) cam-type deformity resulted in adjusted OR of 3.67 (95% CI 1.68 to 8.01) and 9.66 (95% CI 4.72 to 19.78), respectively, for end-stage osteoarthritis. The combination of severe cam-type deformity and decreased internal rotation at baseline resulted in an even more pronounced adjusted OR, and in a positive predictive value of 52.6% for end-stage osteoarthritis. For incident osteoarthritis, only a moderate cam-type deformity was predictive OR=2.42 (95% CI 1.15 to 5.06). Conclusions Individuals with both severe cam-type deformity and reduced internal rotation are strongly predisposed to fast progression to end-stage osteoarthritis. As cam impingement might be a modifiable risk factor, early recognition of this condition is important.