Cui Quanwei

Prof. Dr. Cui Quanwei


Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
8 October 2024 in International Journal of Material Forming
Verified
Journal Article
Closed access
PDF file
LLLi Linjie
Li Linjie
CQCui Quanwei
Cui Quanwei
ZJZhou Jianxing
Zhou Jianxing
SWSun Wenlei
Sun Wenlei
LZLu Zhicheng
Lu Zhicheng
GWGuo Wanli
Guo Wanli

28 September 2024 in Materials
Verified
Journal Article
Open access
PDF file
LLLinjie Li
Linjie Li
CQCui Quanwei
Cui Quanwei
JZJianxing Zhou
Jianxing Zhou
LZl zc
l zc
HSHaoran Sun
Haoran Sun
AWAn Wu
An Wu
In order to explore the influence of laser power on the evolution of molten pool and convective heat transfer of laser cladding Incoloy 926 on stainless steel surface, a three-dimensional thermal fluid multi-field coupled laser cladding numerical model was established in this paper. The variation of latent heat during solid-liquid phase transformation was treated by apparent heat capacity method. The change in the gas–liquid interface was tracked using the mesh growth method in real time. The instantaneous evolution of temperature field and velocity flow field of laser cladding Incoloy 926 on a stainless steel surface under different laser power was discussed. The solidification characteristic parameters of the cladding layer were calculated based on the temperature-time variation curves at different nodes. The mechanism of the impact of laser power on the microstructure of the cladding layer was revealed. The experiment of laser cladding Incoloy 926 on 316L surface was carried out under different laser power. Combined with the numerical simulation results, the effects of laser power on the geometrical morphology, microstructure and element distribution of the cladding layer were compared and analyzed. The results show that with the increase in laser power, the peak temperature and flow velocity of the molten pool surface both increase significantly. The thermal influence of the molten pool center on the edge is enhanced. The temperature gradient, solidification rate, and cooling rate increased gradually. The microstructure parameters (G/R) are relatively small when the laser power is 1000 W. In the experimental range, the dilution rate and wetting angle of the cladding layer both increase with the increase in laser power. When the laser power is 1000 W, the alloying elements of the cladding layer are more evenly distributed and the microstructure is finer. The experimental results are in good agreement with the simulation results.

4 January 2026 in Journal of Bio- and Tribo-Corrosion
Verified
Journal Article
Closed access
PDF file
HZHanxin Zhou
Hanxin Zhou
CQCui Quanwei
Cui Quanwei
AWAn Wu
An Wu
JZJianxing Zhou
Jianxing Zhou

1 November 2025 in Materials Research Express
Verified
Journal Article
Open access
CQCui Quanwei
Cui Quanwei
WGWanli Guo
Wanli Guo
WWWenxiao Wang
Wenxiao Wang
LLLinjie Li
Linjie Li
ZLZhicheng Lu
Zhicheng Lu
HSHaoran Sun
Haoran Sun
In multi-pass and multi-layer laser cladding, significant thermal accumulation occurs in the clad layers. This thermal accumulation causes substantial fluctuations in the molten pool’s temperature field. It also induces significant variations in the flow field. Consequently, these changes affect the microstructure, formation quality, and mechanical properties of the clad layer. This study develops a finite element model that integrates heat transfer, fluid flow, and free surface dynamics to simulate the multi-layer deposition of IN718 alloy onto a 45 steel substrate. The model reveals the dynamic evolution of the temperature and flow fields under the influence of thermal accumulation during multi-layer deposition. Numerical results demonstrate that interlayer thermal accumulation exerts a more substantial influence than multi-pass overlapping. A continuous decrease in temperature gradient is observed throughout the entire process. After the first pass, the gradient measures 1.53 × 10 6 K m −1 . It then declines sharply during interlayer deposition. The gradient ultimately reaches 8.5 × 10 5 K m −1 by the end of cladding. This represents a total reduction of 44.4%. The molten pool flow velocity exhibits an initial increase from 0.42 m s −1 to 0.45 m s −1 , followed by a decrease and eventual stabilization at 0.37 m s −1 . With progressive deposition, insufficient edge support leads to increasingly severe gravity-driven pool inclination, particularly evident in the final pass of each layer. The average error between the temperature measurements and the simulation results is 4.42%. Furthermore, the simulated pool morphology aligns closely with experimental cross-sections, confirming the model’s reliability.

25 June 2025 in Modelling and Simulation in Materials Science and Engineering
Verified
Journal Article
Closed access
CQCui Quanwei
Cui Quanwei
LLLi Linjie
Li Linjie
GWGuo Wanli
Guo Wanli
LZLu Zhicheng
Lu Zhicheng
SHSun Haoran
Sun Haoran
In order to explore the influence of ultrasonic assistance on the evolution law of microstructure in laser cladding, a dynamic model of dendrite growth in ultrasonic-assisted laser cladding is established in this paper. The phase field control equation is established based on the coupling of the phase field method and the temperature field. Ultrasonic vibrations of different amplitudes are added in the form of high-frequency disturbances in the phase field control equation. The morphological characteristics of dendrite growth with and without the action of ultrasonic energy field are analyzed. The influence law of ultrasonic amplitude on the morphological evolution behavior of dendrites in laser cladding layers is discussed. The solidification structure of the cladding layer is experimentally characterized through ultrasound-assisted laser cladding experiments to verify the reliability of the simulation results. In the ultrasound-assisted laser cladding experiments with the same amplitude, the refinement degree of the microstructure of the cladding layer is the most significant, and its microhardness is the greatest.

17 September 2026 in Surface Engineering
Verified
Journal Article
Closed access
XWXiong Wei
Xiong Wei
CQCui Quanwei
Cui Quanwei
ZLZhou Li
Zhou Li
HYHuang Yong
Huang Yong
Laser additive manufacturing of IN718 superalloy claddings is frequently hampered by severe hot cracking and inadequate geometrical uniformity, making precise control of operational variables indispensable. In response, this investigation systematically tailored three pivotal parameters—namely, laser power (P), overlap ratio (D), and powder feed rate (V f )—with the aim of diminishing crack prevalence and elevating coating quality. Initial orthogonal experiments were conducted to delineate the parametric influence trends. Subsequently, a back-propagation neural network, synergistically optimized via a genetic algorithm and particle swarm optimization (GA-PSO-BPNN),was proposed for quantifying the relationship correlating the processing variables with the resulting crack density,yielding high-precision prediction (R 2  > 0.97) and thereby facilitating a global optimization strategy. Empirical findings reveal that the ranking of factor significance on crack density is P > D > V f . The optimal configuration, identified as 650 W, 6.3 r/min, and 24% overlap, successfully produced the lowest crack density of 0.024827 ± 0.00092 mm/mm 2 . Confirmatory deposition experiments substantiate that the resultant coating displays favorable macro-morphology, devoid of observable defects or metallurgical irregularities. Collectively, these outcomes corroborate that hybrid machine-learning paradigms outperform traditional design-of-experiment methodologies, offering a time-efficient, highly precise, and robust tool for refining the processing conditions to achieve the desired cladding morphology.