The clinical performances of dental materials depend on their mechanical profiles, determining their long-term deformation and wear resistance. This paper describes a study on the mechanical properties, water absorption and morphological properties of a polymethyl methacrylate (PMMA) resin enriched with graphene-silver nanoparticles (Gr-Ag). Two different concentrations—1 and 2 wt.%—of Gr-Ag were loaded into the PMMA material. For the mechanical characterization, the compression behavior, flexural strength and tensile strength were evaluated. Optical microscopy in polarized light and scanning electron microscopy were used for filler analysis. The filler addition led to an improvement in all mechanical properties, with slight changes being derived from the filler content variation. Gr-Ag use led to an increase in the applied maximum loads. Moreover, 1 wt.% Gr-Ag determined an increase of 174% in the modulus of rupture, which indicates high flexibility.

The metal-ceramic fixed partial prosthesis is the golden standard for posterior tooth restorations. Following the demands of patients and clinicians for metal-free restorations, all-ceramic materials were developed as they offer an adequate alternative with better optical qualities and good mechanical properties. This study aims to carry out a bibliographic review to assess the survival rate and the biological and technical complications of all-ceramic and metal-ceramic fixed partial dentures. An electronic search for articles in the English language literature was performed using PubMed (MEDLINE). This literature review focused on research studies between 2010 and 2020 that performed clinical studies on tooth-supported fixed partial dentures with a mean follow-up of at least 3 years. All the studies, which analyzed the survival and complications of tooth-supported fixed partial dentures, were included. Thus, 14 studies reporting on 756 all-ceramic and 160 metal-ceramic fixed partial dentures met the inclusion criteria. A comparative analysis was carried out based on all the data existing in the studies included in this review. The metal-ceramic fixed partial dentures showed survival rates of 95% to 100% at 3-, 5-, and 10-year follow-up periods. Zirconia fixed partial dentures were reported to have survival rates of 81% to 100% at 3-, 5-, 9-, 10-year follow-up evaluations. The reinforced glass-ceramic fixed partial dentures showed survival rates of 70% to 93.35% at 5 years, while the alumina FPDs showed a survival rate of 68% at 3 years follow-up. The incidence of caries and loss of vitality were reported as higher for all-ceramic prostheses as compared to the metal-ceramic ones. A significant framework fracture was reported for glass-infiltrated alumina fixed partial dentures in comparison to metal-ceramic fixed partial dentures. All-ceramic and metal-ceramic restorations showed similar survival rates after 3 years, although all-ceramic restorations have problems with technical complications such as chipping, which can lead to framework fractures over time.

(1) Background: Poor hygiene and denture presence in the oral cavity are factors that favor bacterial accumulation, the cause of halitosis and of various oral and general diseases. Aim: This study aimed to evaluate the possibility of inactivating bacteria associated with halitosis in acrylic denture wearers using polymethyl methacrylate resin enhanced with graphene silver nanoparticles and the effect of the resin association with extra oral photodynamic therapy. (2) Methods: Graphene silver nanoparticles in 1 and 2 wt% were added to a commercial acrylic resin powder. Three study groups containing samples from the three different materials were established. The first group was not exposed to the light treatment, and the other two were exposed to red light (laser and light emitting diode) after photosensitizer placement on the disk’s surface. Samples were incubated with Porphyromonas gingivalis and Enterococcus faecalis. (3) Results: For both bacterial strains, inhibition zones were obtained, showing significant differences for the light-treated samples. (4) Conclusions: Denture resins with antibacterial properties associated with extra oral photodynamic therapy exhibited enhanced antibacterial effects. The procedure could be used as a safer and more efficient alternative technique against halitosis and oral infections in denture wearers.

In this study, the biological activities of four extracts from Vitis vinifera by-products: two pomace extracts, white (WPE) and red (RPE), a canes extract (CE), and their combination (CoE), were evaluated, to be included in freeze-drying mouthwashes formulations. The cytocompatibility and anticancerous potential of the four extracts were tested on three cancerous cell lines, as well as the cytoprotective activity against nicotine-induced cytotoxicity and the antioxidant potential determined on a human gingival fibroblasts (HGF) cell line. Additionally, the anti-inflammatory activity and the antimicrobial activity against several microorganisms from the oral microbiome were tested. Freeze-dried mouthwashes with CoE were prepared and characterized, both as lyophilizates and after reconstitution. The four tested extracts showed the highest cytotoxicity on MDA-kb2 cell line. The antioxidant potential was demonstrated for WPE, RPE, CE, and CoE, both in non-stimulated and H₂O₂ stimulated conditions. The four extracts reduced the levels of proinflammatory cytokines (IL-6, IL-8, and IL-1β) in a dose-dependent manner, confirming their anti-inflammatory activity. The antimicrobial activity of tested extracts was shown against pathogenic bacteria from the oral microbiome. Mouthwashes of CoE with poloxamer-407, xylitol, and different ratios of mannitol were prepared by freeze-drying leading to porous formulations with interesting mechanical properties and reconstitution times.

Dental crown marginal adaptation is a matter of the success of dental restoration treatment. Nowadays, there are many technological ways for crown manufacturing, such as tridimensional printing of an exactly desired shape through CAD-assisted systems and the appropriate shape milling of a predesigned bulk crown. Both methods are developed for patient benefits. The current research aims to investigate the marginal adaptation of E-Max crowns manufactured by printing-pressed and milling methods. The in vitro cementation procedures were effectuated on healthy teeth extracted for orthodontic purposes according to the standard procedures and the marginal adaptation was investigated with SEM microscopy. The restoration overview was inspected at a magnification of 100× and the microstructural details at 400×. The integrity of marginal adaptation was properly inspected in identical samples on segments of 2 mm from each buccal, palatal, distal and mesial side. The obtained results reveal a good marginal adaptation for all samples, with some particularities. The statistical analysis shows that the best values of the marginal adaptation were obtained for vestibular/buccal and palatal sides of the teeth being situated around 90–95%, while the values obtained for distal and mesial sides are slightly lower such as 80–90%. Furthermore, it was observed that the milled crowns presents better marginal adaptations than the printed-pressed ones, sustained by the statistical p < 0.05. This indicates that the milling process allows a better fit of the crown to the tooth surface and preserves the integrity of the bonding cement layer.

Background/Objectives: Osteoporosis is a common general disease that mostly affects the skeletal system, including the jawbone. There is a link between systemic and mandibular osteoporosis. This study aimed at assessing the association between systemic (lumbar spine L1–L4, femoral neck, total hip) bone mineral density (BMD) and mandible BMD sites in Romanian postmenopausal females. Methods: A total of 97 menopausal patients were studied, 62 with osteoporosis and 35 females with no osteoporosis. For each patient, dual-energy X-ray absorptiometry (DXA) assessments of BMD in the mandible, proximal femur, total hip, and lumbar spine (L1–L4) were performed. Mandibular measurements were performed using the distal forearm software, followed by manual analysis after the bone contour was defined in each case. Results: Comparing the osteoporosis and control groups, there were significant differences in BMD at each examined location. The mandibular BMD (1.125 ± 0.181506 g/cm²) in the osteoporosis group was considerably smaller than in the control group (1.35497 ± 0.244397 g/cm²). Correlations between the BMD at different sites were significant: lumbar spine and femoral neck (r = 0.738, p < 0.0001), lumbar spine and total hip (r = 0.735, p < 0.0001), lumbar spine and mandible (r = 0.506, p < 0.0001), femoral neck and total hip (r = 0.891, p < 0.0001), femoral neck and mandible (r = 0.482, p < 0.0001), and total hip and mandible (r = 0.466, p < 0.0001). Conclusions: There were correlations between mandible BMD and lumbar spine, femoral neck, and total hip BMD, suggesting that osteoporosis affects mandibular bone density. BMD assessments at common locations may help predict mandibular BMD and the probability of osteoporosis.