Maria Kirgina

Dr. Maria Kirgina


Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
19 January 2022 in Applied Sciences
Verified
Journal Article
Open access
PDF file
KLKirill Larionov
Kirill Larionov
AKAlbert Kaltaev
Albert Kaltaev
KSKonstantin Slyusarskiy
Konstantin Slyusarskiy
DGDmitriy V. Gvozdyakov
Dmitriy V. Gvozdyakov
AZAndrey Zenkov
Andrey Zenkov
VGVladimir Gubin
Vladimir Gubin
Experimental studies of the steam pyrolysis of oil sludge were performed using a flow-type pilot plant with 300 kg/h capacity (raw material) to obtain energy-valuable products, such as liquid hydrocarbons (30.4 wt%), semi-coke (39.6 wt%), non-condensable gas-phase compounds (26.5 wt%), and bitumen (3.5 wt%). The pyrolysis process was conducted at a temperature of 650 ° C and with a steam flow rate of 150 kg/h. Liquid hydrocarbons were considered a target product. Comprehensive studies of their physicochemical characteristics, atomization process, droplet ignition, and combustion were carried out. The studied sample had physicochemical characteristics similar to traditional fuel oil (calorific value—42.6 MJ/kg, sulfur content—0.8 wt%). The jet spraying angle was 25° in view of the improved rheological properties of the test sample, with a homogeneous jet structure and a predominant droplet diameter of no more than 0.4 mm. The flame combustion process was accompanied by the formation of microexplosions, the frequency and intensity of which depended on the temperature of the air (Tg = 450–700 °C). This study, in view of its applied nature, is of interest in the design of new installations and technological systems for hydrocarbon pyrolysis.

7 June 2021 in Oil & Gas Science and Technology – Revue d’IFP Energies nouvelles
Verified
Journal Article
Open access
PDF file
MKMaria Kirgina
Maria Kirgina
IBIlya Bogdanov
Ilya Bogdanov
AAAndrey Altynov
Andrey Altynov
NBNataliya Belinskaya
Nataliya Belinskaya
AOAlina Orlova
Alina Orlova
NNNurguyaana Nikonova
Nurguyaana Nikonova
One of the most widely used way to improve low-temperature properties of diesel fuels is the use of additives. However, a variety of additives and the effect of susceptibility make it difficult to select additive for a particular composition of diesel fuel and operating conditions. The laws of interaction between functional groups of additives and hydrocarbons of the diesel fraction have not been investigated yet. The article discusses the influence of fractional, group and structural-group composition of straight-run diesel fuels on the effectiveness of cold flow improvers. The effect of additives concentration on the effectiveness of their action is considered. It was shown that when selecting a cold flow improver for diesel fuel and determining its optimal concentration, it is necessary to take into account the optimal content of various groups of hydrocarbons in diesel fuel, at which a cold flow improver is most effective.

7 October 2023 in Chemengineering
Verified
Journal Article
Open access
PDF file
AAAltynov Andrey
Altynov Andrey
IBIlya Bogdanov
Ilya Bogdanov
DLDaniil Lukyanov
Daniil Lukyanov
MKMaria Kirgina
Maria Kirgina
Natural gas liquids are a by-product of natural gas preparation, one of the most common and environmentally friendly energy sources. In natural gas fields located in remote areas, there is no resource-efficient way to use natural gas liquids. However, natural gas liquids are a valuable hydrocarbon feedstock for the production of motor fuels, in particular motor gasolines. The aim of this work is to develop a method for obtaining motor gasolines by processing natural gas liquids on a zeolite catalyst, taking into account the influence of the particle size of the zeolite catalyst, the technological parameters of the process, and the composition of the feedstock. As part of the work, for the first time, regularities of the influence of zeolite catalyst particle size, technological parameters of the process and the composition of feedstock on the composition and characteristics of the resulting processed products were revealed. A database about the composition and characteristics of natural gas liquids, obtained from various gas fields in Western Siberia of the Russian Federation, has been accumulated. During the study, it was found that the optimal particle size of the zeolite catalyst is 0.50–1.00 mm; optimal technological parameters are a temperature of 375 °C, pressure 2.5 atm. and the feedstock space velocity 2 h−1. It is shown that the processing of natural gas liquids of various compositions on a zeolite catalyst, on average, makes it possible to increase their detonation resistance by more than 16 points. The results obtained indicate the prospects of using the process for the production of motor gasoline. The paper presents a number of blending recipes for obtaining fuels, both within the framework of production at the fields and at processing plants.

6 January 2024 in Applied Sciences
Verified
Journal Article
Open access
PDF file
ATAlina Titaeva
Alina Titaeva
IBIlya Bogdanov
Ilya Bogdanov
KTKirill Titaev
Kirill Titaev
YMYana Morozova
Yana Morozova
MKMaria Kirgina
Maria Kirgina
The use of depressant additives is the most common method for producing diesel fuels with improved low-temperature properties. However, the depressants effectiveness largely depends on the composition of the diesel fuel, in particular on the content of n-paraffinic hydrocarbons, which to the greatest extent determine the low-temperature properties of the fuel. The work revealed the regularities of the n-paraffins addition influence on the depressant additives effectiveness. It was found that the addition of n-paraffins to blends of diesel fuels with depressants in low concentrations (0.05–0.50% wt.) enhances the depressants effectiveness in relation to the cold filter plugging point: maximum at 6–16 °C depending on the diesel fuel sample. It is shown that the effect is observed for DF of various compositions, various depressants, and also n-paraffins of various compositions. It was established that the positive effect of adding n-paraffins increases with the heavier added n-paraffins. Recommendations have been developed for obtaining diesel fuels with improved low-temperature properties and enhancing the depressant additives effectiveness: for a sample of straight-run diesel fuel F1, it is recommended to use a blend of fuel, depressant A1 and 0.50% wt. n-paraffins, separated from heavy gasoil; for a sample of straight-run diesel fuel F2, it is recommended to use a blend of fuel, depressant A2 and 0.50% wt. n-paraffins, separated from heavy gasoil or a blend of fuel, depressant A1 and 0.05% wt. n-paraffins, separated from highly paraffinic oil fraction. The revealed patterns and the developed recommendations will allow increasing the production of low-freezing DF brands, and also offer a resource-efficient option for using heavy gas oil fractions. The results obtained in the work contribute to expanding the understanding of the mechanism of interaction between diesel fuel hydrocarbons and the active ingredients of depressant additives.

1 January 2014 in Procedia Chemistry
Verified
Journal Article
Open access
BSB.V. Sakhnevitch
B.V. Sakhnevitch
MKMaria Kirgina
Maria Kirgina
NCN.V. Chekancev
N.V. Chekancev
EIE.D. Ivanchina
E.D. Ivanchina
ASA.A. Syskina
A.A. Syskina
The main aim of the study is to increase the efficiency of gasoline blending process using developed complex modeling system, it provides counting feedstock changes in the refinery, influencing detonation characteristics of trade gasoline. Final products of modeling system are precise and gasoline blending recipes are economically optimal. The relevance of the study is caused by the need to increase production volumes of trade gasoline in refineries that meet gasoline quality standards. Mathematical modeling and application of automatic computer systems are most relevant solutions for optimization of technologically difficult stages of oil production. The study considers the modeling approach to the blending process from the position of non-additivity of gasoline octane numbers. Practical results: The module of gasoline detonation characteristics developed in Borland "Delphi 7" workspace in conjunction with the module of chromatographic data analysis "Unichrom" and optimal recipes development module are combined in the universal complex system for gasoline blending process maintenance. The system allows taking into account feedstock composition changes on purpose to vary the recipes of trade gasoline blending. The developed complex system analyzes refinery conditions and recommends the feedstock supply in the process and allows getting essential economic benefit for the refineries by reducing the quality reserve of trade products

11 July 2024 in Resources
Verified
Journal Article
Open access
PDF file
DSDaria Sosnina
Daria Sosnina
AAAltynov Andrey
Altynov Andrey
MKMaria Kirgina
Maria Kirgina
IBIlya Bogdanov
Ilya Bogdanov
Nowadays, there is a need to search for new renewable energy sources from which it is possible to obtain hydrocarbons that are similar in composition and properties to hydrocarbons of petroleum origin. This is due to a significant increase in demand for natural minerals and, as a consequence, the depletion of their reserves. Today, the most promising alternative renewable energy sources are various vegetable oils, which are used both in their pure form, adding them to commercial mineral fuels, and as products of catalytic processing using various catalysts. However, most studies in the field of alternative energy show that the use of fuels obtained from vegetable oils is limited by their properties as well as the climatic conditions of the areas where biofuels can be used. In this work, we propose an integrated approach to the processing of vegetable oils, which allows us to obtain products of a wide fractional composition with improved operational properties. This approach consists of sequential processing of vegetable oils, first using a CoMo/Al2O3 hydrotreating catalyst in order to obtain classical long-chain hydrocarbons with unsatisfactory properties, and then using a zeolite catalyst, ZSM-5 type, which is characterized by the active occurrence of cracking, isomerization, and aromatization reactions, which are accompanied by a decrease in the length of the hydrocarbon chain of the hydrocarbons obtained during the hydrotreating process and, as a result, improving the physicochemical and low-temperature properties of the resulting processed products.