This paper describes a design of a power transfer inductive link for charging batteries of wireless sensor network nodes. The application physical constraints imposes a maximum size for the coils and demands a design methodology to maximize output power delivered to the load and energy transmission efficiency. This paper presents a complete methodology for designing the coils of wireless power transfer systems applied to rechargeable batteries of wireless sensor network nodes. The design of an inductive link is presented as a case study, in which two planar coils are built in order to validate the proposed method. Moreover, a complete wireless power transfer system is developed for the proposal, including coils, primary power source, capacitor network compensation, and secondary power management, with rectification, filtering, regulation, and battery charge control. The experimental results for working distances between the coils from 1 mm to 10 mm are reported as well as the frequency response of the entire system.
22 January 2014 in IEEE Transactions on Instrumentation and Measurement
This paper introduces the analysis of the efficiency and transferred power of an inductive link circuit with different network configurations of capacitors connected to primary and secondary coils. The best performance for both cited objective functions was observed with two capacitors connected to the input coil and two capacitors connected to the output coil. However, the output equations in this circuit configuration for both efficiency and output power are very complex and a numerical method had to be applied to compute the capacitors values. Since an exhaustive search would be long, some simplifications were assumed to reduce the search space and the processing time. Thus, a search algorithm based on a randomized method was developed and successfully applied. The results for both efficiency and output power of four capacitors configuration were compared with other usual approaches, such as the single and two capacitors compensation. Finally, a basic prototype was built and the theoretical results were validated. Both simulated and experimental results of the four capacitor configuration showed a significant improvement on the efficiency and output power of the inductive link.
A novel full four capacitor compensation method for inductive power transfer is introduced. To compute the capacitors values, a very simple search algorithm based on Monte Carlo is used. In addiction, some heuristic are used to reduce the size of the search space. The efficiency, output power and power efficiency are compared with some classical approach such as the two capacitors compensation and also with the basic circuit without compensation. The results showed a significant improvement on the efficiency and output power.
The wireless power transfer efficiency plays an important role in design of implantable biomedical devices. There are some important constraints in the design, such as the size of the implantable coil as well as the power delivered to the implant. In this context, this paper presents the design of two planar spiral coils coupled by air used to transferring energy wirelessly. The geometric constraints of the application are determined to define the dimensions of the coils. These parameters along with the working frequency of the system are applied to a procedure that results in the equivalent electrical model characterization of the coils, as well as mutual inductance. A capacitor matching network is then determined in order to optimize two objective functions: efficiency of the whole link and power transferred to the load. Since in a practical application the values of the capacitors are discrete and limited to a commercial series of values, we developed a numerical procedure to conduct a search of the best results of both objective functions. This network is characterized by being made up of a series-parallel network at both the input and output. The sequence of this work includes the development of an oscillator used as the primary voltage source and the experimental evaluation of the entire system.
Defect detection in metallic plates represents an important issue in metal industry, because its potential use in quality control process. Eddy current testing is one of the most extensively used nondestructive techniques for inspecting electrically conductive materials. The purpose of this paper is to present an eddy current testing system for surface defect detection in conducting materials using a giant magnetoresistive (GMR) sensor. An alternate magnetic field is produced by a solenoid and eddy currents are generated in the material under test. The GMR sensor was mounted inside the coil and the arrangement was adapted in the axis of a vertical machining center. In order to validating the measurement device, defects were induced by cracks machined in workpieces made of aluminum. Thus, the parts were scanned with the sensor prototype and a method to estimate the width and depth of the induced defects was proposed after analyzing the output voltage signal.
Milk has a high nutritional value and is also one of the most versatile products in the food industry. Unfortunately, fraud involving the product is constant and needs to be combated. This work presents a measurement methodology to perform the electrical impedance analysis in food. The influence of temperature on the measurements has been evaluated through mathematical models specially developed for identifying the fraudulent activity of adding water to milk. The bioimpedance measurements have been performed in a sample container with a four-electrode measurement system and a digital oscilloscope. Samples of 150 mL were analysed, prepared using whole UHT milk adulterated with distilled water in different % by volume (V/V), at temperatures of 16, 28, and 37 °C. The proposed measurement methodology has been validated and showed sensitivity for analysis in milk, revealing the influence of temperature on the impedance values; from the results mathematical models were proposed for investigating adulteration in milk. This work deals with the design of a device capable of measuring bioimpedance in milk with a view to its application in physicochemical analyses. The influence of temperature on the impedance values was also evaluated to propose mathematical models to facilitate analysis with complex factors and matrices.