The optical band gap of ZnO thin films deposited on fused quartz by metal-organic chemical-vapor deposition was studied. The optical band gap of as-grown ZnO blueshifted from as the growth temperature decreased from . After annealing, the optical band gap shifted back to the single-crystal value. All the ZnO thin films studied show strong band-edge photoluminescence. X-ray diffraction measurements showed that samples deposited at low temperatures consisted of amorphous and crystalline phases. The redshift of the optical band gap back to the original position after annealing was strong evidence that the blueshift was due to an amorphous phase. The unshifted photoluminescence spectra indicated that the luminescence was due to the crystalline phase of ZnO, which was in the form of nanocrystals embedded in the amorphous phase.
Tubular ZnO microstructural arrays were fabricated by a hydrothermal decomposition method. The dependence of the morphologies on the growth time and temperature was investigated in detail. An experiment was carried out to determine the mechanism of tubular ZnO formation. Our results showed that ZnO microtubes originated from an ageing process from ZnO microrods at a lower temperature (compared to the temperature when hydrothermal deposition of ZnO microrods was dominant) due to the preferential chemical dissolution of the metastable Zn-rich (0001) polar surfaces. A growth model was proposed based on the coexistence of hydrothermal deposition and dissolution of ZnO in the fabrication process.
Formamidinium lead halide (FAPbX3) has attracted greater attention and is more prominent recently in photovoltaic devices due to its broad absorption and higher thermal stability in comparison to more popular methylammonium lead halide MAPbX3. Herein, a simple and highly reproducible room temperature synthesis of device grade high quality formamidinium lead bromide CH(NH2)2PbBr3 (FAPbBr3) colloidal nanocrystals (NC) having high photoluminescence quantum efficiency (PLQE) of 55–65% is reported. In addition, we demonstrate high brightness perovskite light emitting device (Pe-LED) with these FAPbBr3 perovskite NC thin film using 2,2′,2″-(1,3,5-Benzinetriyl)-tris(1-phenyl-1-H-benzimidazole) commonly known as TPBi and 4,6-Bis(3,5-di(pyridin-3-yl)phenyl)-2-methylpyrimidine (B3PYMPM) as electron transport layers (ETL). The Pe-LED device with B3PYMPM as ETL has bright electroluminescence of up to 2714 cd/m2, while the Pe-LED device with TPBi as ETL has higher peak luminous efficiency of 6.4 cd/A and peak luminous power efficiency of 5.7 lm/W. To our knowledge this is the first report on high brightness light emitting device based on CH(NH2)2PbBr3 widely known as FAPbBr3 nanocrystals in literature.
Recently, CsPbBr3 perovskites have been emerging as very promising green emission materials for light-emitting diodes (LEDs) due to their high color purity, low cost and high photoluminescence quantum yield (PLQY). However, the corresponding LED performance is still low and far behind CH3NH3PbBr3; it is due to the lack of proper perovskite film preparation methods and interfacial engineering. Herein, we report highly bright and durable CsPbBr3-based LEDs fabricated using a one-step solution method. The precursor solution is prepared by simply dissolving CsPbBr3 powder and a CsBr additive in dimethyl sulfoxide (DMSO). We find that the CsBr additive not only significantly enhances the PLQY but also induces directional crystal growth into micro-plates, forming a smooth perovskite film for LEDs. LEDs employing such high quality films show a high luminance of 7276 cd m−2 and high color purity with a full width at half maximum of 18 nm. Furthermore, the as-fabricated LEDs reveal an outstanding ambient stability with a decent luminance output (>100 cd m−2, steady increase without any degradation trend) for at least 15 h under a constant driving current density (66.7 mA cm−2). And we propose two reasons for this unique luminance increasing behavior: (1) the CsPbBr3 perovskite is thermally stable and can survive from joule heat; and (2) on the other hand, the joule heating will induce interface or crystalline film annealing, reduce device resistance and then enhance the luminance output.
An inverted organic solar cell based on poly(3-hexylthiophene) (P3HT) and 1-(3-methoxycarbonyl)-propyl-1-phenyl- (PCBM) was fabricated with an ultrathin Ca electron-transporting layer and hole-transporting layer. The 1 nm Ca on indium tin oxide (ITO) electrode modifies the work function of ITO suitable for electron extraction. An appropriate thickness of hole extraction layer is also essential to effectively prevent exciton quenching at the Ag anode, yet not introduce much voltage loss and series resistance. The optical field distribution across the active layer was also simulated to discuss the effect of thickness on the photocurrent. The maximum power conversion efficiency obtained was 3.55% under simulated (AM 1.5G) solar irradiation.