Petra Maier

Prof. Petra Maier

University of Applied Sciences Stralsund
orcid

Research Focus & Metrics

Academic Career Length

14Years (2013-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 December 2021 in MRS Bulletin
Verified
Journal Article
Open access
PDF file
Timothy LipmanTimothy Lipman
Timothy Lipman
PMPetra Maier
Petra Maier
Electric vehicles are now proliferating based on technologies and components that in turn rely on the use of strategic materials and mineral resources. This review article discusses critical materials considerations for electric drive vehicles, focusing on the underlying component technologies and materials. These mainly include materials for advanced batteries, motors and electronics, lightweight structures, and other components specific to each vehicle type. Particularly strategic and widely used minerals and elements/structures for electric vehicles include nickel, cobalt, rare-earth minerals, lightweight and high strength steel alloys and underlying metals (e.g., magnesium and aluminum), carbon fiber, graphite and graphene, copper, and steel alloying materials. Additional key considerations include those around component and vehicle supply chains, repurposing and recycling vehicle components at end of vehicle life, and environmental and humanitarian considerations around the extraction and transport of the evolving set of materials needed for modern electric vehicle production. Graphical abstract

5 October 2020 in Metals
Verified
Journal Article
Open access
PDF file
PMPetra Maier
Petra Maier
Norbert HortNorbert Hort
Norbert Hort
Interest in magnesium alloys as biodegradable metals has strongly grown over the last decades

29 December 2015 in JOM
Verified
Journal Article
Closed access
PDF file
PMPetra Maier
Petra Maier
RPR. Peters
R. Peters
CMChamini L. Mendis
Chamini L. Mendis
SMS. Müller
S. Müller
Norbert HortNorbert Hort
Norbert Hort

14 August 2018 in Metals
Verified
Journal Article
Open access
PDF file
PMPetra Maier
Petra Maier
MBMaximilian Bechly
Maximilian Bechly
CMChamini L. Mendis
Chamini L. Mendis
Norbert HortNorbert Hort
Norbert Hort
To improve the mechanical and corrosion properties of Mg10Gd, Nd and La are added, and from that, the influence of precipitation hardening was studied. An increase in strength, by decreasing grain size and increasing the volume fraction of Rare Earth-rich precipitates, has been found when increasing the amount of alloying elements. Alloys containing La appear less ductile. Where crack propagation is studied using 3-point bending on Mg10Gd and Mg10Gd1Nd, the failure is mostly driven by twinning; the alloys with La show suppressed twinning, but crack initiation and propagation is caused by brittle and coarse precipitates. Precipitation hardening did not improve fracture toughness and was mostly based on strong grain growth and low solubility of La in Mg. With added alloying elements, the grain size was found to be slightly smaller in the T6 condition—precipitates seem to pin grain boundaries and therefore limit grain boundary mobility. Alloys containing Nd showed the best precipitation hardening response. Corrosion behavior, investigated by voltammetry and immersion, showed the best behavior in the precipitation-hardened condition. Corrosion rates and surface morphology are used to discuss corrosion properties.

24 February 2020 in JOM
Verified
Journal Article
Open access
PDF file
PMPetra Maier
Petra Maier
ASA. Steinacker
A. Steinacker
BCB. Clausius
B. Clausius
NHN. Hort
N. Hort
The microstructural changes and corrosion response of Resoloy®, a resorbable Mg-Dy-based alloy, are the focus of this study. Hardness, tensile and compressive, and bending tests are used to monitor the changes in the mechanical properties of this material. The corrosion behavior is investigated by stress corrosion of C-rings. Hot-extruded tubes are solution heat-treated at different temperatures and times. The as-extruded condition shows a homogeneous fine-grained microstructure with matrix long-period stacking-ordered (LPSO) structures. Heat treatment at low temperatures and for short times does not significantly change the microstructure but reduces the hardness. Solution heat treatment at relatively high annealing temperatures and long annealing times causes grain growth, resulting in reduced hardness. The microstructure becomes inhomogeneous, medium-sized grains grow, the matrix LPSO structures dissolve, and small bulk LPSO phases develop. The matrix LPSO structures have a positive effect on the corrosion behavior. In particular, the short-term annealing condition shows the most uniform corrosion morphology. Resoloy® is not free of pitting corrosion, but none of the samples fails by cracking.

17 July 2017 in Materials and Corrosion
Verified
Journal Article
Closed access
PDF file
PMPetra Maier
Petra Maier
FZF. Zimmermann
F. Zimmermann
MRM. Rinne
M. Rinne
GSG. Szakács
G. Szakács
NHN. Hort
N. Hort
CVC. Vogt
C. Vogt