Wescley Tiago Batista de Sousa

Dr. Wescley Tiago Batista de Sousa

orcid

Research Focus & Metrics

Academic Career Length

18Years (2009-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
11 July 2022 in Superconductor Science and Technology
Verified
Journal Article
Open access
Mohammad Yazdani AsramiMohammad Yazdani Asrami
Mohammad Yazdani Asrami
SSSeyyedmeysam Seyyedbarzegar
Seyyedmeysam Seyyedbarzegar
ASAlireza Sadeghi
Alireza Sadeghi
WSWescley Tiago Batista de Sousa
Wescley Tiago Batista de Sousa
DKDustin Kottonau
Dustin Kottonau
Along with advancements in superconducting technology, especially in high-temperature superconductors (HTSs), the use of these materials in power system applications is gaining outstanding attention. Due to the lower weight, capability of carrying higher currents, and the lower loss characteristic of HTS cables, compared to conventional counterparts, they are among the most focused large-scale applications of superconductors in power systems and transportation units. In near future, these cables will be installed as key elements not only in power systems but also in cryo-electrified transportation units, that take advantage of both cryogenics and superconducting technology simultaneously, e.g., hydrogen-powered aircraft. Given the sensitivity of the reliable and continuous performance of HTS cables, any failures, caused by faults, could be catastrophic, if they are not designed appropriately. Thus, fault analysis of superconducting cables is crucial for ensuring their safety, reliability, and stability, and also for characterising the behaviour of HTS cables under fault currents at the design stage. Many investigations have been conducted on the fault characterisation and analysis of HTS cables in the last few years. This paper aims to provide a topical review on all of these conducted studies, and will discuss the current challenges of HTS cables and after that current developments of fault behaviour of HTS cables will be presented, and then we will discuss the future trends and future challenges of superconducting cables regarding their fault performance.

1 July 2014 in Cryogenics
Verified
Journal Article
Closed access
WSWescley Tiago Batista de Sousa
Wescley Tiago Batista de Sousa
APA. Polasek
A. Polasek
RDR. Dias
R. Dias
CMC.F.T. Matt
C.F.T. Matt
RAR. de Andrade
R. de Andrade

29 January 2021 in Superconductor Science and Technology
Verified
Journal Article
Closed access
PDF file
YLYingzhen Liu
Yingzhen Liu
Jing OuJing Ou
Jing Ou
RGRoland Gyuraki
Roland Gyuraki
FSFabian Schreiner
Fabian Schreiner
WSWescley Tiago Batista de Sousa
Wescley Tiago Batista de Sousa
FGFrancesco Grilli
Francesco Grilli
Previous studies of test coils have demonstrated the high thermal and electrical stability of no-insulation (NI) high temperature superconducting (HTS) coils thanks to the presence of turn-to-turn current paths. These turn-to-turn current paths in a NI coil are significantly influenced by the contact resistivity. In practice, it is very challenging to measure the contact resistivity of a NI coil by direct experiments of short samples, since the contact resistivity of superconducting tapes is influenced by surface roughness and tolerance, stress, temperature etc. A proper simulation model is needed to investigate the contact resistivity of the NI coils with dedicated experiments. Hence, in this paper a distributed circuit model is employed. This model, implemented in Matlab 2018a, considers the local contact resistivity, self and mutual inductance, and HTS resistance, which depends on the supplied current, magnetic field and temperature. To validate the model, experimental results from literature, including sudden discharge, and charge–discharge processes, are employed and the results from simulations are consistent with experimental results. Then the model is used to investigate the equivalent contact resistivity of a 157-turn NI coil. Through the comparison of simulated and experimental results, it is found that the contact resistivity of the NI coil has an inhomogeneous distribution. When the current changes with different speeds, ramping rates or frequency, a different number of turn-to-turn contacts carries radial current. Since the turn-to-turn contacts have different contact resistivity, the equivalent contact resistivity calculated from sudden discharge cannot be used in simulations to reproduce all the experimental data.

5 March 2012 in IEEE Transactions on Applied Superconductivity
Verified
Journal Article
Closed access
WSWescley Tiago Batista de Sousa
Wescley Tiago Batista de Sousa
APA. Polasek
A. Polasek
FSF. A. Silva
F. A. Silva
RDR. Dias
R. Dias
AJA. R. Jurelo
A. R. Jurelo
RAR. de Andrade
R. de Andrade
Superconducting fault current limiters (SCFCLs) represent a promising solution to the problem of increasing short- circuit currents in the grid. The SCFCL is based on the fast transition from the superconducting state to the normal state, causing a sudden increase in the impedance of the network. In this paper, we simulate the behavior of resistive-type SCFCL modules. The SCFCL modules are based on MCP-BSCCO 2212 coils. The superconductor acts as a nonlinear resistance that varies with the current and the temperature. The behavior of the simulated curves is consistent with the experimental results. Short-circuit currents as high as 37 kApeak were limited to about 10% of their peak values in the first half cycle.

7 December 2020 in Superconductor Science and Technology
Verified
Journal Article
Closed access
WSWescley Tiago Batista de Sousa
Wescley Tiago Batista de Sousa
ESE Shabagin
E Shabagin
DKD Kottonau
D Kottonau
MNM Noe
M Noe
Advances in superconductor technology make the prospect of economical operation of high temperature superconducting (HTS) power cables a practical concept for grid applications in urban centers. With more advanced cable designs being developed and commercialized, their geometrical features and dynamic behavior are becoming increasingly complicated to be modeled. This brings new challenges as the complex structure of HTS power cables significantly increases the computation power needed to perform simulations. In this paper we develop a two-dimensional open source simulation code based on the finite difference method which is solved by means of the alternating direction implicit routine. The algorithm has been written in MatLab programming language. The method improves computational performance and simulation time. In addition, this enables the creation of open-source simulation codes. A three-phase concentric HTS cable design has been chosen for the development of the code, nevertheless the model can be employed for any cable design. The results indicate an efficient, stable and powerful simulation code. During the development no numerical instabilities have been found. Besides that, the model is able to deliver quantities that are experimentally difficult to access. Simulation files are available for the scientific community on the HTS Modeling Workgroup webpage. 1 1 Simulation files can be downloaded. here .

12 March 2014 in IEEE Transactions on Applied Superconductivity
Verified
Journal Article
Closed access
WSWescley Tiago Batista de Sousa
Wescley Tiago Batista de Sousa
ONOliver Nackel
Oliver Nackel
MNMathias Noe
Mathias Noe
Simulations of superconducting fault current limiters (SFCL) devices become more crucial in order to predict their behavior before installing them into power systems. There are different approaches for modeling SFCLs, whereas computational simulations provide a better understanding of the behavior of SFCL devices. This paper presents three different models to simulate an air-coil SFCL that differ from each other by considerations of heat exchanges. Simulation results were compared with short-circuit tests. The results show that a good agreement between simulations and tests can be found if the heat exchanges between the different layers of high-temperature superconducting tapes are considered. The development of equivalent resistance and the increase in temperature of the superconducting tapes were also obtained.