Albendazole (ABZ, anti-parasitic active pharmaceutical ingredient) is a crystalline low water-soluble drug, thus the dissolution rate in gastrointestinal fluids is limited. Consequently, the improvement of the water solubility and dissolution rate of ABZ implies a great challenge for a more efficient treatment of hydatidosis. In this context, SBA-15 and SBA-16 ordered mesoporous silica materials were synthetized and loaded with ABZ. X-ray diffraction, FT-IR spectroscopy, nitrogen physisorption manometry, particle size distribution and scanning electronic microscopy were used to characterize unloaded and loaded materials (ABZ/SBA-15 and ABZ/SBA-16). The loaded ABZ amount in the carriers was estimated by elemental analysis. For the loaded materials, the drug solubility and release profile were evaluated. In addition, mathematical models were compared to explain the dissolution kinetics of ABZ from mesoporous solids. ABZ was successfully loaded into the mesopores. The amorphous state of the adsorbed ABZ was confirmed by differential scanning calorimetry that resulted in a notable increment in the dissolution rate compared to crystalline ABZ. Drug release behaviors were well simulated by the Weibull model for ABZ/SBA-15 and by the Gompertz function for pure ABZ and ABZ/SBA-16. The SBA-15 carrier exhibited the highest drug loading and dissolution rate becoming a promising material to improve ABZ bioavailability.

The fabrication through FDM 3D printing of hollow systems intended for oral drug delivery constitutes an attractive technology to change personalized medications in the compounding pharmacy. In this sense, this work studied the design and 3D printing of one compartment capsular devices filled of drugs that could require a delayed release mechanism. The optimization of printing parameters such as material flow rate and printing speed by means of simple gcode modifications, resulted critical to allow the production of PVA capsular devices in a single manufacturing process. In addition, the disintegration and dissolution studies of the obtained capsular device confirmed the existence of a delayed drug release compared to commercial hard-gelatin capsules. Furthermore, the use of sinkers in the dissolution tests resulted in similar dissolution profiles regardless the rotation speed. Finally, Gompertz and Weibull equations were the kinetic models that best fitted the experimental data corresponding to immediate release with lag time type profiles. Overall, this work provides insights to understand the effect of the printing parameters on the production of PVA capsular devices and suggests a simple design and single manufacturing process that can be adopted in the future compounding pharmacy.

Valeriana officinalis L. (Valerianaceae) is one of the most widely used plants for the treatment of anxiety and insomnia. Usually dry plant extracts, including V. officinalis, are hygroscopic materials with poor physico-mechanical properties that can be directly compressed.A V. officinalis dry extract with moderate hygroscocity is suitable for direct compression, and was obtained by using a simple and economical technique. The V. officinalis fluid extract was oven-dried with colloidal silicon dioxide as a drying adjuvant. The addition of colloidal silicon dioxide resulted in a dry plant extract with good physico-mechanical properties for direct compression and lower hygroscopicity than the dry extract without the carrier. The dry plant extract glass transition temperature was considerably above room temperature (about 72 °C). The colloidal silicon dioxide also produced an antiplasticizing effect, improving the powder's physical stability.The pharmaceutical performance of the prepared V. officinalis dry extract was studied through the design of tablets. The manufactured tablets showed good compactability, friability, hardness, and disintegration time. Those containing a disintegrant (Avicel PH 101) exhibited the best pharmaceutical performance, having the lowest disintegration time of around 40 seconds.

The feasibility to obtain highly porous collagen-based scaffolds (SCs) integrated with uniformly dispersed poly(lactide-co-glycolide) (PLGA) microparticles (MPs) was evaluated. PLGA-MPs were prepared by double emulsion technique and SCs with different amounts of MPs (SC/PLGA-MPs) were produced. Results showed that SC/PLGA-MPs could be successfully manufactured, the PLGA-MPs being physically retained in the SCs, without affecting the porous structure. PLGA-MPs also increased the SC hydrophilicity, acted as a mechanical reinforcement and retarded the degradation rate. In addition, the interactions between MPs and Caco-2 cells did not interfere with the correct morphological, adhesion and proliferation pathways.

The aim of this work was to study the effect of gas microbubbles on the production of particles suitable for inhalatory administration by a spray drying technology. An antiasthmatic model drug (sodium cromoglycate) was selected in order to evaluate the effect of different gases (air, CO₂ and N₂) and spray drying operating conditions on the particles aerosolization performance. To this end, gas supersaturated aqueous drug solutions were obtained in a pressurized vessel and then processed by spray drying. The process yield, morphology, size, bulk and tap densities, moisture content and aerosolization properties of the particles were evaluated. The presence of microbubbles in the spray drying feed led to powders with smaller mean geometric sizes than particles obtained without bubbles. The gas-water solubility emerged as a key parameter to obtain inhalatory particles with good aerosolization properties. High water-soluble gases led to bigger particles, while low soluble ones allow to produce smaller particles. The use of air (with an intermediate water solubility respect to CO₂ and N₂) and an adequate set of spray drying operating conditions allowed to obtain sodium cromoglycate particles with superior aerosolization properties than a commercial formulation. Overall, a novel, simple and low-cost method to produce inhalatory particles with excellent aerosolization properties was developed by supersaturating the spray drying liquid feed without using pore-forming agents during the production step, or carriers in the final formulation.