PLA-based blends were prepared with different ratios of PBS, PBAT and TPS additives to adjust their mechanical and processing properties in various temperatures ( − 20 °C, 0 °C, 20 °C, 40 °C). Biodegradable polymeric specimens were obtained by preliminary extrusion and subsequent injection molding. Tensile properties, e.g., tensile strength, elongation at break, Young’s modulus and yield strength were evaluated. Next, melt flow and melt volume ratios were established. Softening, glass transition, cold crystallization and crystallization temperatures were determined with the use of the DSC method. Heat Deflection Temperatures for 1.8 MPa (HDT A) and 8 MPa (HDT C), as well as Vicat Softening Temperatures at 10 N (VST A) and 50 N (VST B), were examined. The manufacturing method was intentionally simplified to eliminate the need for additional mixture’s modification with compatibilizers. Each of the ductile compounds enhanced the deformability of PLA—most significantly in the case of PBAT and TPS, while at the same time reducing its tensile strength. The effect of the test conditions (strain rate and temperature) on the specimens was evaluated in order to determine the stability of the manufactured blends in dependence on these parameters.

This publication presents an innovative tower cultivation device designed to significantly increase vertical farming’s efficiency. The device divides the cultivation system into separate chambers. One division corresponds to the different growth phases of the plants, while another reflects the daily variation in conditions. Each chamber presents slightly different conditions and cultivation patterns from the others. For the early stages, crops are grown horizontally in trays; once they mature, they are transplanted into mobile cultivation towers. The closed circulation of ventilation and irrigation reduces water consumption by up to 95%. A unique separate day–night division optimises light, temperature, and humidity conditions, mimicking natural growth patterns. This approach not only saves water and energy but also improves cultivation in a three-dimensional space. The presented solution focuses on the often-overlooked aspects of cultivating in vertical farms and makes this method of growing much more cost-effective and feasible to implement on a large scale. Our comparative analysis with other vertical farming solutions is based on publicly available data and provides valuable insights, while acknowledging the potential limitations at play.

Replacing elements made of conventional plastics (like polystyrene) with biodegradable substitutes is part of the trend of sustainable development and waste reduction. The manuscript covers issues related to the design, manufacturing and testing of sports helmet protective inserts made of biodegradable material. The FEM numerical simulations carried out by the authors allowed to determine the optimal desirable mechanical properties (R _e = 8.5–65 MPa, E = 500–8000 MPa for 30 × 30 mm inserts; R _e = 10.5–60 MPa, E = 500–7500 MPa for 48 × 48 mm inserts; R _e = 13–95 MPa, E = 400–8500 MPa for 55 × 55 mm inserts) and geometric parameters (wall thickness equal to 0.2–0.5 mm, height of 20 mm), ensuring the formation of a plastic fold, which is the most effective energy-absorbing mechanism. The conducted quasi-static compression, bending and dynamic tensile strength tests allowed to determine blends with appropriate proportions of durable PLA with more plastic PBAT, PBS and TPS that meet the established criteria: PLA50PBAT50, PLA30PBAT70 and PLA30TPS70.

The publication presents an innovative tower cultivation device designed to significantly increase vertical farming efficiency. The device divides the cultivation system into separate chambers. One division corresponds to the different growth phases of the plants, while another reflects the daily variation in conditions. Each chamber presents slightly different conditions and cultivation patterns from the others. For the early stages, crops are grown horizontally in trays once they mature, transplanted into mobile cultivation towers. The closed circulation of ventilation and irrigation reduces water consumption by up to 95%. A unique separate day-night division optimises light, temperature and humidity conditions, mimicking natural growth patterns. This approach not only saves water and energy but also optimises cultivation in a three-dimensional space. The presented solution focuses on the often overlooked aspects of cultivating in vertical farms and makes this method of growing much more cost-effective and feasible to implement on a large scale.

This article addresses manufacturing structures made via injection molding from biodegradable materials. The mentioned structures can be successfully used as energy-absorbing liners of all kinds of sports helmets, replacing the previously used expanded polystyrene. This paper is focused on injection technological tests and tensile tests (in quasi-static and dynamic conditions) of several composites based on a PLA matrix with the addition of other biodegradable softening agents, such as PBAT and TPS (the blends were prepared via melt blending using a screw extruder with mass compositions of 50:50, 30:70, and 15:85). Tensile tests showed a positive strain rate sensitivity of the mixtures and a dependence of the increase in the ratio of the dynamic to static yield stress on the increase in the share of the plastic component in the mixture. Technological tests showed that increasing the amount of the plasticizing additive by 35% (from 50% to 85%) results in a decrease in the minimal thickness of the thin-walled element that can be successfully injection molded by about 32% in the case of PLA/PBAT blends (from 0.22 mm to 0.15 mm) and by about 26% in the case of PLA/TPS blends (from 0.23 mm to 0.17 mm). Next, the thin-walled elements (dimensions of 55 × 55 × 20 mm) were manufactured and evaluated using a spring-loaded drop hammer. The 60 J impact energy was tested in accordance with the EN 1078 standard. The dynamic crushing test included checking the influence of the materials’ temperature (−20, 0, 20, and 40 °C) and the impact velocity. It was proven that the maximum deflection increases with increasing material temperature and an increase in the share of the plastic component in the mixture. The PLA15PBAT85 blend was selected as the most effective material in terms of its use as an energy-absorbing liner for sport helmets. Johnson–Cook and Cowper–Symonds material plasticizing models were constructed. Their use during dynamic FE simulation provided results that were in good agreement with those of the conducted experiment.

The article addresses manufacturing structures made of biodegradable materials that can be successfully used as energy-absorbing liner of sports helmets of all kinds, replacing the previously used expanded polystyrene. The paper is focused on injection technological tests and tensile tests (in quasi-static and dynamic conditions) of several composites based on a PLA matrix with the addition of other biodegradable softening agents, such as PBAT and TPS. Next, the thin-walled elements (dimensions of 55 x 55 x 20 mm) were manufactured and evaluated using a spring-loaded drop hammer. The 60J impact energy was tested according to EN 1078 standard. The dynamic crushing testing included checking the influence of the materials temperature (-20, 0, 20, and 40 °C) and the impact velocity. The PLA15PBAT85 blend was selected as the most effective material in terms of its use as energy-absorbing liner for sport helmets.