A clay mineral-type modified bentonite, produced via delamination and subsequent incorporation of AlZr and AlCe species to modulate their acid properties, was used to obtain bifunctional catalysts with the incorporation of NiMo, CoMo, NiW and CoW. The catalysts were characterized using X-ray diffraction (XRD), N2 adsorption, scanning electron microscopy (SEM), temperature-programmed reduction (H2-TPR) and diffuse reflectance infrared Fourier-transform spectra with a probe molecule (NH3-DRIFTS). The catalytic performance was evaluated in the hydroconversion of decane. The main differences in catalytic performance were attributed to the reductive and acid properties of the catalysts. Indeed, when Mo was used, there was a higher conversion compared to W catalysts, which correlated with the greater number of reducible species at lower temperatures. Solids with a promoter/metal ratio of 0.4 presented the best catalytic performance, which is attributed to the fact that this ratio improves the formation of NiW, NiMo, CoW and CoMo species on the surface of solids. On the other hand, the catalysts obtained from the mineral modified with AlCe showed better catalytic activity compared to catalysts containing AlZr as an acidity enhancer. The different processes and elements used give us information to carry out controlled processes for the generation of acid sites that respond to a specific orientation of the decane hydroconversion reaction.
The use of plasmonic nanoparticles for biosensor technology is dependent on nanoparticle size and morphology. This study determined the effect of pH and pressure on synthesizing silver nanoparticle size. In Method 1, a mixture of NaBH4 and sodium citrate was added to a solution of AgNO3 monodispersed by ultrasound energy. In Method 2, the reducer was added to the precursor–dispersant mixture solution. The effect of pH was evaluated by using buffer solutions at pH 4.0, pH 7.0, and pH 10.0 and water as control. To determine the effect of pressure, AgNPs were subjected to 0, 4, and 23 h to 1.75 MPa at 200 °C. AgNPs produced with Method 1 showed a more symmetric SPR and a smaller nanoparticle diameter (±6 nm). The SPR with Method 1 at pH 10.0 produced a higher UV peak with a shift around 20 nm. In the case of the pressure treatment, a shift of approximately 20 nm was observed at all time conditions studied, and a higher AgNP diameter was found in contrast to Method 1. Finally, EDX and Raman analysis confirm the presence of AgNPs and a mild oxidation of these. These results suggest that alkalinity and pressure can affect the diameter of AgNPs.
13 October 2022 in Reaction Chemistry & Engineering
Ni bifunctional catalysts supported on vermiculite, halloysite and bentonite previously modified by means of delamination or acid treatment were synthesized. The Ni was incorporated using three synthesis methods: auto-combustion (AC), microwave-assisted auto-combustion (AM) and the wet impregnation method (WI). The solids obtained were characterized under different conditions: i) as oxides prior to the reaction, using X-ray diffraction (XRD), N2 physisorption and temperature programmed reduction (H2-TPR), ii) under “in situ” reaction conditions using infrared spectroscopy with probe molecule (NH3-DRIFTS) accompanied by titration with HCl, iii) “ex situ” using high resolution transmission electron microscopy (HRTEM) and iv) post-reaction catalysts were characterized using thermogravimetric analysis (TGA-DSC), Raman and infrared spectroscopy. The catalytic performance of the materials was evaluated in the hydroconversion of decane (C10). In addition, the influence of the impregnation method on the mineral used was analyzed. In the case of the solids obtained from bentonite and halloysite, the methods that most favored the catalytic activity were those of auto-combustion, while in the case of the catalysts obtained with vermiculite as a support, the most favorable method was wet impregnation (WI), which was related to the number of reducible species, the dispersion and acid properties that each method favored depending on the clay mineral used. Finally, all the catalysts presented a high resistance to the formation of carbonaceous residues on their surface, indicating a high activity and low deactivation of the materials.