The goal of this manuscript is to investigate the influence of relative distance between the twin rotors on the hydrodynamic performance of the vertical axis twin-rotor tidal current turbine. Computational fluid dynamics (CFD) simulations based on commercial software ANSYS-CFX have been performed to enhance the understanding of interactions between the twin-rotors. The interactions between the twin rotors are known to have increased the power output efficiency as a whole, and it is, therefore, of great significance to undertake deeper research. The simulation results are found to be consistent with similar research results in the literature in some aspects. The simulation results of stand-alone turbine and twin rotors are compared from three different aspects, including blade forces, power output efficiency and wake flow field. The results showed that the cyclic variations tendency of blade force coefficients of twin rotors is close to that of the stand-alone turbine. The average power output efficiency of the twin-rotors system is higher than that of the stand-alone turbine. The interactions between the turbines increase the power output of the twin turbine system as whole in a wide relative distance range. However, smaller relative distance between the twin rotors does not mean a bigger power output efficiency of such a system. The power out efficiency of such a system would decrease when the relative distance between the twin rotors exceeds the critical point. The power output of the twin rotors reaches the peak value when the ratio between the two main axis distance and diameter of the turbine is around 9/4. This research can provide a reference for the design and development of larger tidal power stations.
For a current turbine fixed on a floating platform, the wave-induced motion responses of the platform change the hydrodynamic performance of the current turbine. In this paper, a numerical simulation method based on commercial computational fluid dynamics software-CFX is established to systematically analyze the turbine loads condition and power output efficiency of the turbine subject to the wave-induced motion. This method works well in terms of 2D hydrodynamic performance analysis and is verified by an experiment. In addition, the method is applied to investigate the hydrodynamic performance of a vertical axis current turbine under forced oscillation by a combining sliding mesh with moving mesh technique. This research mainly focusses on the effects of oscillation frequency and oscillation amplitude on the hydrodynamic performance and the flow field. It is found that a wake flow similar to the Von Karman Vortex Street appears under sway oscillation. Spacing between vortex in the wake flow changes under surge oscillation. The fluctuations of the blade load coefficients can be decomposed into a low frequency part and a high frequency part. The low frequency part is related to the frequency of the forced oscillation, while the high frequency part is a consequence of the rotational frequency of the turbine. The oscillation amplitudes of the turbine load coefficients increase linearly with the growth of oscillation frequency and oscillation amplitude. This paper can provide a useful reference for similar research on the turbine loads condition and power out efficiency of the turbine subject to wave-induced motion. This paper can also provide a reference on the structural design or electronic control of vertical axis current turbines.
Plate structures are the main components of offshore platforms and ships in engineering applications. The vibration control of the low-frequency mode of plate structures has always been a meaningful research object in marine science and engineering. Due to their low cost and good performance, dynamic vibration absorbers are widely used. To enhance the design efficiency of dynamic vibration absorbers, a mathematical model was developed for plates with dynamic vibration absorbers under different boundary constraints. To overcome the discontinuity of the displacement function, auxiliary series were introduced. In addition, the efficiency of resolving the plate structure’s equivalent mass was significantly improved compared with when using FEM software Abaqus 6.14. The validity of the proposed mathematical model was confirmed in comparison with related studies, the FEM results, and the experimental results. Considering the mathematical model and design approach proposed in the current paper, more research on the vibration control of plates subjected to clamped and elastic boundary conditions should be performed. The mathematical model and findings in the design process may have positive implications for the control of the vibration of plate structures in marine science and engineering.
Coupled plate structures composed of stiffened plates and sub-plates have been widely used in marine engineering practice. Meanwhile, the low-frequency multi-linear spectrum vibration control of the coupled stiffened plate structures has become necessary and meaningful. However, the design efficiency of the dynamic vibration absorber of the corresponding structure is still low. In the present study, a mathematical model of coupled plate structures and a dynamic vibration absorber is introduced to improve design efficiency. Subsequently, an experiment is designed to verify the effectiveness and advantages of the current method. The reliability of the current mathematical model is verified by comparing it with modal experiment results. Moreover, the equivalent mass solution efficiency is greatly improved by comparing it with FEM. Finally, a comparison experiment of the dynamic vibration absorber has also been conducted to further verify the effectiveness of the current method. The semi-analytical method proposed in the current research may be useful when designing dynamic vibration absorbers for the coupled plate structures of offshore platforms.