Implant-associated infections caused by Staphylococcus aureus are a growing problem for healthcare systems. Implant materials that resist bacterial colonization may help reduce infection rates and severity. This research examined the effect of a copper-coated carbon-infiltrated carbon nanotube surface (Cu-CICNT). We have previously shown that CICNT without copper has an anti-biofilm effect, and copper has long been known to have anti-bacterial properties. Bacterial biofilms were grown in a droplet on the Cu-CICNT surface, and a control consisting of copper deposited on a relatively flat, non-nanotube-structured surface. The Cu-CICNT surface was highly effective at reducing biofilm formation, reducing recoverable S. aureus bacteria by 99.9999% in 12 hours (a 6.3-log reduction). This effect was confirmed in both a methicillin-resistant and a methicillin-sensitive isolate of S. aureus . The Cu-CICNT surface was also highly effective against Pseudomonas aeruginosa , resulting in a 6.9-log reduction in adherent bacteria. The Cu-CICNT surface was more effective at inhibiting biofilm formation than the flat copper-coated titanium, indicating a synergistic effect between the CICNT topography and copper. The concentration of copper ions in growth media was low after exposure to Cu-CICNT (6.2 ppm), and media with this amount of supplemented copper had only a small effect on biofilm reduction, as did conditioned media previously exposed to Cu-CICNT. Our findings suggest that the antibacterial effect is likely due to contact killing of bacteria on the textured copper surface. IMPORTANCE: Orthopedic implants and devices are becoming increasingly common. Unfortunately, as their use increases, so does the prevalence of implant-associated infections. These infections are most commonly caused by the bacterium Staphylococcus aureus. S. aureus infections are particularly difficult to treat because they form biofilms resistant to antibiotics and the host immune system. In this research, we used a carbon nanotube-based surface combined with a thin film of copper to produce a surface coating that could be used on implants to prevent bacterial infection. The combination of the surface topography with the copper coating resulted in over a 6-log reduction in the number of adherent bacteria, preventing the formation of a bacterial biofilm. This reduction in adherent bacteria is likely due to the surface killing effects of the bacteria on contact. The potential applications of such a surface could help reduce infection burden, improve patient quality of life, and reduce stress on healthcare systems.
Acquired immunodeficiency syndrome (AIDS) occurs when HIV depletes CD4+ helper T cells. Some patients develop AIDS slowly or not at all, and are termed long-term non-progressors (LTNP), and while mutations in the HIV-1 Viral Protein R (vpr) gene such as R77Q are associated with LTNP, mechanisms for this correlation are unclear. This study examines the induction of apoptosis, cell cycle arrest, and pro-inflammatory cytokine release in the HUT78 T cell line following infection with replication-competent wild-type strain NL4-3, the R77Q mutant, or a vpr Null mutant. Our results show a significant enhancement of apoptosis and G2 cell cycle arrest in HUT78 cells infected with R77Q, but not with WT NL4-3 or the vpr Null strain. Conversely, HUT78 cells infected with the WT virus show higher levels of necrosis. We also detected lower TNF and IL-6 release after infection with R77Q vs. WT. The apoptotic phenotype was also seen in the CEM cell line and in primary CD4+ T cells. Protein expression of the R77Q vpr variant was low compared to WT vpr, but expression levels alone cannot explain these phenotypes because the Null virus did not show apoptosis or G2 arrest. These results suggest that R77Q triggers a non-inflammatory apoptotic pathway that attenuates inflammation, possibly contributing to LTNP.
Orthopedic implant-associated infections are a growing problem. These infections are often associated with bacterial biofilms, such as those formed by Staphylococcus aureus. Nanotextured surfaces can reduce or prevent the development of bacterial biofilms and could help reduce infection rates and severity. Previous work has shown that a carbon-infiltrated carbon nanotube (CICNT) surface reduces the growth of S. aureus biofilms. This work expands on previous experiments, showing that the topography of the CICNT, rather than its surface chemistry, is responsible for the reduction in biofilm growth. Additionally, the CICNT surface does not reduce biofilm growth by killing the bacteria or by preventing their attachment. Rather it likely slows cell growth, resulting in fewer cells and reduced biofilm formation.