This study investigates the influence of fiber dimensions on the bridging performance of polyvinyl alcohol fiber-reinforced cementitious composite (PVA-FRCC) through an experimental and analytical program. Bending tests, bridging law calculations, and section analysis are conducted. Bending tests of notched specimens of PVA-FRCC with six different PVA fiber dimensions are performed to determine the load–deflection (LPD) and bending moment–crack mouth opening displacement (CMOD) relationships. The fiber volume fraction for all PVA-FRCCs is set to 2%. It is found that the load capacity of PVA-FRCC with a 27 μm diameter fiber is much higher than that of the other fibers, and the load capacity decreases as the fiber diameter increases. The study proposes parameters for the characteristic points of the tri-linear model for the single-fiber pullout model as functions of diameter, bond fracture energy, elastic modulus, cross-sectional area, and perimeter of the fiber. These findings provide valuable insights into the behavior of PVA-FRCC under different fiber dimensions. Bridging law calculations are conducted to obtain tensile stress–crack width relationships using the developed single-fiber pullout models. The Popovics model for the complete tensile stress–crack width relationship is adopted to obtain a better fit with the bridging law calculation, and then section analysis is conducted. The bridging law calculation results show that the maximum tensile stress decreases as the fiber diameter increases. It is also determined that most of the smaller-diameter fibers ruptured, whereas the larger fiber diameters pulled out from the matrix. The section analysis results show good agreement with the maximum bending moments obtained from the bending test.
The integration of fiber-reinforced cementitious composites (FRCCs) with fiber-reinforced polymer (FRP) bars represents a significant advancement in concrete technology, aimed at enhancing the structural performance of reinforced concrete elements. The incorporation of fibers into cementitious composites markedly improves their mechanical properties, including tensile strength, ductility, compressive strength, and flexural strength, by effectively bridging cracks and optimizing load distribution. Furthermore, FRP bars extend these properties with their high tensile strength, lightweight characteristics, and exceptional corrosion resistance, rendering them ideal for applications in aggressive environments. In recent years, there has been a notable increase in interest from the engineering research community regarding this topic, primarily to solve the issues of aging and deteriorating infrastructure. Researchers have conducted extensive investigations into the structural performance of FRCC and FRP composite systems. This paper presents a systematic literature review that surveys experimental and analytical studies, findings, and emerging trends in this field. A comprehensive search on the Web of Science identified 40 relevant research articles through a rigorous selection process. Key factors of structural performance, such as bond behavior, flexural behavior, ductility performance assessments, shear and torsional performance, and durability evaluations, have been documented. This review aims to provide an in-depth understanding of the structural performance of these innovative composite materials, paving the way for future research and development in construction materials technology.
This study addresses the growing need for sustainable construction materials by investigating the mechanical properties and behavior of palm fiber-reinforced cementitious composite (FRCC), a potential eco-friendly alternative to synthetic fiber reinforcements. Despite the promise of natural fibers in enhancing the mechanical performance of composites, challenges remain in optimizing fiber distribution, fiber–composite bonding mechanism, and its balance to matrix strength. To address these challenges, this study conducted extensive experimental programs using palm fiber as reinforcement, focusing on understanding the fiber–matrix interaction, determining the pullout load–slip relationship, and modeling fiber bridging behavior. The experimental program included density calculations and scanning electron microscope (SEM) analysis to examine the surface morphology and diameter of the fibers. Single fiber pullout tests were performed under varying conditions to assess the pullout load, slip behavior, and failure modes of the palm fiber, and a relationship between the pullout load and slip with the embedded length of the palm fiber was constructed. A trilinear model was developed to describe the pullout load–slip behavior of single fibers, and a corresponding palm-FRCC bridging model was constructed using the results from these tests. Section analysis was conducted to assess the adaptability of the modeled bridging law calculations, and the analysis result of the bending moment–curvature relationship shows a good agreement with the experimental results obtained from the four-point bending test of palm-FRCC. These findings demonstrate the potential of palm fibers in improving the mechanical performance of FRCC and contribute to the broader understanding of natural fiber reinforcement in cementitious composites.
This study aims to verify the adaptability of a crack width evaluation method for fiber-reinforced cementitious composite (FRCC) proposed by the authors to various combinations of fiber-reinforced polymer (FRP) bars and FRCCs. As this evaluation method requires bond constitutive laws between FRP bars and FRCC, bond tests between FRP and FRCCs were conducted. The FRP and FRCC combinations used in the bond tests were spiral-type CFRP and GFRP bars with PVA-FRCC, as well as strand-type CFRP bars with aramid–FRCC. The maximum bond stress tended to increase as the rib–height ratio of the spiral-type bars increased. When the rib–height ratio increased by 50%, the maximum bond stress of the CFRP and GFRP bars increased by 11% and 33%, respectively. For aramid–FRCC, the average maximum bond stress in the FRCC with a 0.25% volume fraction was 1.67 times that in mortar, and that in 0.50% was 2.01 times that in mortar. The bond constitutive laws were modeled using the trilinear model. Verifications of the method’s adaptability were conducted using tension tests on prisms made of spiral-type CFRP and GFRP bars with PVA-FRCC. As a result of the tension tests, when the FRP strain reached approximately 0.3%, the crack width was about 0.2 mm for CFRP bars and about 0.1 mm for GFRP bars. Verifications were also conducted using four-point bending tests on strand-type CFRP bar beams with aramid–FRCC. The crack width at the same FRP strain tended to become smaller as the fiber volume fraction of FRCC increased. When the FRP strain reached approximately 0.2%, the average crack width of the mortar specimen was around 0.25 mm, whereas it was about 0.15 mm in FRCC with a 0.25% volume fraction and about 0.10 mm at 0.5%. The test results for FRP strain versus crack width relationships were compared with the calculations using the crack width prediction formula. The test results and calculation results were in good agreement.
5 November 2026 in The Open Construction & Building Technology Journal
Introduction/Objective: This study investigates the flexural and equivalent tensile behaviour of polyester fiber-reinforced ductile fiber-reinforced cementitious composite (PES-DFRCC) incorporating commercially available Indian-manufactured polyester fibers. The influence of fiber volume fraction on the flexural response and equivalent tensile properties was evaluated through four-point bending tests and inverse section analysis. This study presents the first experimental investigation of PES-DFRCC using this methodology and establishes its equivalent tensile stress–strain behaviour. Methods: Beam specimens containing different polyester fiber volume fractions were tested under four-point bending in accordance with ISO 21914:2019. Load, axial deformation, and deflection measurements were recorded, and tensile properties were determined through inverse section analysis based on the observed flexural response. Results: The PES-DFRCC specimens exhibited multiple microcracking and pronounced deflection-hardening behavior under bending. The evaluated average tensile strength ranged from 0.34 to 2.41 MPa, while the corresponding average ultimate tensile strain varied from 0.276% to 0.450%, depending on the fiber content. Discussion: The formation of multiple microcracks contributed to enhanced ductility and energy absorption capacity, indicating the effectiveness of polyester fibers in improving the post-cracking performance of cementitious composites. Conclusion: The newly developed PES-DFRCC demonstrated significant ductile behavior, characterized by multiple cracking, deflection hardening, and improved tensile performance. These findings highlight the potential of polyester fiber reinforcement for developing durable and ductile cementitious materials for structural applications.