Hai Wang

Prof. Dr. Hai Wang

School of Mechanical Engineering, Anhui Polytechnic University, Wuhu, Anhui, China
orcid

Research Focus & Metrics

Academic Career Length

36Years (1991-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
18 March 2024 in IEEE Transactions on Instrumentation and Measurement
Verified
Journal Article
Closed access
LLLirui Liao
Lirui Liao
SZShuneng Zhou
Shuneng Zhou
JYJunfeng Yang
Junfeng Yang
ZWZekun Wang
Zekun Wang
JLJingjie Li
Jingjie Li
LWLi Wen
Li Wen
Flexible pressure sensors are an essential component in artificial systems to monitor human health. Recently, flexible pressure sensors with micro-nanostructures in interlocked geometry have attracted extensive attention because they effectively improve the sensing performance. However, it is a challenge that the fabrication methods are complex and expensive, and the layered interface between microstructure and nanostructure is unstable. Here, a flexible pressure sensor with an interlocked polydimethylsiloxane (PDMS) micropillars array combined secondary nanoprotrusions on their surfaces is proposed, which can be shaped in one step with merits of simplicity, controllability and low cost. The unique combined micro-nanostructures ensure the sensor with a wide linear range (0~32 kPa), relatively high piezoresistive sensitivity (26.08 Ω/kPa), low detection limit (15 Pa), fast response speed (response time is 56 ms, and relaxation time is 140 ms) and excellent stability (>1000 cycles). These superior properties set a foundation for applying the sensor in detecting various human physiological signals from pulse to joint deformation. Based on this sensor, a smart mask integrated system is proposed, displaying and recording breathing conditions in real time. These results demonstrate that the sensor can be used in health monitoring and disease diagnosis, as well as its potential application in other wearable devices.

19 May 2023 in Actuators
Verified
Journal Article
Open access
PDF file
SLShuai Li
Shuai Li
HLHenian Li
Henian Li
HWHai Wang
Hai Wang
CYChunlai Yang
Chunlai Yang
JGJingsong Gui
Jingsong Gui
RFRonghua Fu
Ronghua Fu
Sliding mode control has been widely used to control permanent magnet synchronous motors (PMSM). However, the parameters of the sliding mode controller are difficult to be tuned, which makes the control performance of PMSM hard to be improved. A nonlinear sliding mode control method that integrated a nonlinear reaching law (NRLSMC) and extended state observer (ESO) is proposed in this paper, whose parameters are tuned by an improved genetic algorithm (IGA). The control performance of the nonlinear reaching law in the nonlinear sliding mode controller is analyzed, whose stability is verified based on the Lyapunov theorem. An extended state observer is integrated into the above controller to further improve the anti-interference capability, and compensate for the observed external disturbance of the system into the speed controller in sliding mode. The optimal parameters of the above sliding mode control are tuned by IGA combined with the system speed loop model. The performance of the proposed controller is numerically simulated in MATLAB/Simulink and verified in a control system rapid control prototype (RCP) experimental platform built based on dSPACE 1202. Numerical simulation and experimental results show that the proposed controller can make the PMSM control system with the advantages of no overshoot, fast response, and strong robustness.

20 April 2018 in Micromachines
Verified
Journal Article
Open access
PDF file
MZMan Zhang
Man Zhang
YDYichuan Dai
Yichuan Dai
LWLi Wen
Li Wen
HWHai Wang
Hai Wang
JCJiaru Chu
Jiaru Chu
A localized maskless modification method of polyurethane (PU) films through an atmospheric pressure He/O2 plasma microjet (APPμJ) was proposed. The APPμJ system combines an atmospheric pressure plasma jet (APPJ) with a microfabricated silicon micronozzle with dimension of 30 μm, which has advantages of simple structure and low cost. The possibility of APPμJ in functionalizing PU films with hydroxyl (–OH) groups and covalent grafting of gelatin for improving its biocompatibility was demonstrated. The morphologies and chemical compositions of the modified surface were analyzed by scanning electronic microscopy (SEM), Raman spectroscopy, and X-ray photoelectron spectroscopy (XPS). The fluorescent images show the modified surface can be divided into four areas with different fluorescence intensity from the center to the outside domain. The distribution of the rings could be controlled by plasma process parameters, such as the treatment time and the flow rate of O2. When the treatment time is 4 to 5 min with the oxygen percentage of 0.6%, the PU film can be effectively local functionalized with the diameter of 170 μm. In addition, the modification mechanism of PU films by the APPμJ is investigated. The localized polymer modified by APPμJ has potential applications in the field of tissue engineering.

14 December 2016 in Micromachines
Verified
Journal Article
Open access
PDF file
QLQiang Li
Qiang Li
JLJie Liu
Jie Liu
YDYichuan Dai
Yichuan Dai
WXWushu Xiang
Wushu Xiang
MZMan Zhang
Man Zhang
LWLi Wen
Li Wen
The prevention of glow-to-arc transition exhibited by micro dielectric barrier discharge (MDBD), as well as its long lifetime, has generated much excitement across a variety of applications. Silicon nitride (SiNx) is often used as a dielectric barrier layer in DBD due to its excellent chemical inertness and high electrical permittivity. However, during fabrication of the MDBD devices with multilayer films for maskless nano etching, the residual stress-induced deformation may bring cracks or wrinkles of the devices after depositing SiNx by plasma enhanced chemical vapor deposition (PECVD). Considering that the residual stress of SiNx can be tailored from compressive stress to tensile stress under different PECVD deposition parameters, in order to minimize the stress-induced deformation and avoid cracks or wrinkles of the MDBD device, we experimentally measured stress in each thin film of a MDBD device, then used numerical simulation to analyze and obtain the minimum deformation of multilayer films when the intrinsic stress of SiNx is −200 MPa compressive stress. The stress of SiNx can be tailored to the desired value by tuning the deposition parameters of the SiNx film, such as the silane (SiH4)–ammonia (NH3) flow ratio, radio frequency (RF) power, chamber pressure, and deposition temperature. Finally, we used the optimum PECVD process parameters to successfully fabricate a MDBD device with good quality.

1 June 2017 in Micromachines
Verified
Journal Article
Open access
PDF file
YDYichuan Dai
Yichuan Dai
MZMan Zhang
Man Zhang
QLQiang Li
Qiang Li
LWLi Wen
Li Wen
HWHai Wang
Hai Wang
JCJiaru Chu
Jiaru Chu
Maskless etching approaches such as microdischarges and atmospheric pressure plasma jets (APPJs) have been studied recently. Nonetheless, a simple, long lifetime, and efficient maskless etching method is still a challenge. In this work, a separated type maskless etching system based on atmospheric pressure He/O2 plasma jet and microfabricated Micro Electro Mechanical Systems (MEMS) nozzle have been developed with advantages of simple-structure, flexibility, and parallel processing capacity. The plasma was generated in the glass tube, forming the micron level plasma jet between the nozzle and the surface of polymer. The plasma microjet was capable of removing photoresist without masks since it contains oxygen reactive species verified by spectra measurement. The experimental results illustrated that different features of microholes etched by plasma microjet could be achieved by controlling the distance between the nozzle and the substrate, additive oxygen ratio, and etch time, the result of which is consistent with the analysis result of plasma spectra. In addition, a parallel etching process was also realized by plasma microjets array.

19 October 2023 in Applied Sciences
Verified
Journal Article
Open access
PDF file
YZYaling Zhao
Yaling Zhao
HWHai Wang
Hai Wang
XXXiaoming Xie
Xiaoming Xie
YXYongzheng Xie
Yongzheng Xie
CYChunlai Yang
Chunlai Yang
The detection of surface defects in metal materials has been a challenging issue in the industrial domain. The existing algorithms for metal surface defect detection are limited to a few specific types of defects and exhibit low performance with detection of defects of varying scales. A novel detection method based on the Information Enhancement YOLOv5 Network (IE-YOLOv5) for surface defects in metal parts is proposed, to realize efficient detection, which introduces a lightweight Federated Fusion Slim Neck module (FF-Slim-Neck) and a Parameter-free Spatial Attention mechanism (PSA) in YOLOv5 network. Comparative experiments were conducted using the NEU-DET dataset. The experimental results indicate that the proposed algorithm for detecting defects on metal surfaces achieves an average precision of 96.7% when identifying six different types of surface imperfections: crazing, inclusions, patches, pitting, scaling, and scratches. This represents a 2.4% enhancement in precision compared to the YOLOv5 algorithm. The measured processing velocity of this approach stands at 46.17 frames per second (FPS), highlighting its remarkable qualities of resilience, precision, and real-time capability.