In recent decades, there have been considerable technological developments in the agriculture sector to automate manual processes for many factors, including increased production demand and in response to labor shortages/costs. We conducted a review of the literature to summarize the key advances from installing emerging technology and studies on robotics and automation to improve agricultural practices. The main objective of this review was to survey the scientific literature to identify the uses of these new technologies in agricultural practices focusing on new or reduced occupational safety risks affecting agriculture workers. We screened 3248 articles with the following criteria: (1) relevance of the title and abstract with occupational safety and health; (2) agriculture technologies/applications that were available in the United States; (3) written in English; and (4) published 2015–2020. We found 624 articles on crops and harvesting and 80 articles on livestock farming related to robotics and automated systems. Within livestock farming, most (78%) articles identified were related to dairy farms, and 56% of the articles indicated these farms were using robotics routinely. However, our review revealed gaps in how the technology has been evaluated to show the benefits or potential hazards to the safety and well-being of livestock owners/operators and workers.
1 September 2023 in Proceedings of the Human Factors and Ergonomics Society Annual Meeting
The Lifting Fatigue Failure Tool (LiFFT) is an ergonomic assessment tool based on fatigue failure theory that uses the lower back load moment to evaluate the risk associated with multi-task jobs involving manual lifting. The current LiFFT tool does not account for the moment associated with flexing the lifter's torso. This study explores the incorporation of torso flexion into the LiFFT model while maintaining the relative simplicity of the original LiFFT tool. Automotive manufacturing workers (n=607) performing various tasks were included in the study. Non-manual material handling (MMH) tasks with no MMH load moment were considered "zero" risk. The moment associated with trunk flexion was considered if a worker flexed at the torso during non-MMH assembly tasks. The torso moment from bending was computed using the "average" worker height and weight for the data set used in this study. The proposed model yielded higher odds ratios than the original model.
1 September 2023 in Proceedings of the Human Factors and Ergonomics Society Annual Meeting
NIOSH researchers are pioneering the study of musculoskeletal health as professional ergonomists. We examine physical and social components of work environments to mitigate musculoskeletal injury risks. Part of our mission is to reduce the burden of work-related musculoskeletal disorders (MSDs) through a focused program of research and prevention that protects workers from MSDs, helps management mitigate related risks and liabilities, and helps practitioners improve the efficacy of workplace interventions. The purpose of this discussion panel is to disseminate research findings and recommendations (1) to practitioners to interpret and apply the results of research to real-world problems, and (2) to inspire researchers to continue their efforts to protect the millions of workers at risk.
The American Conference of Governmental Industrial Hygienists (ACGIH) Threshold Limit Values (TLVs) for lifting provides risk zones for assessing two-handed lifting tasks. This paper describes two computational models for identifying the lifting risk zones using gyroscope information from five inertial measurement units (IMUs) attached to the lifter. Two models were developed: (1) the ratio model using body segment length ratios of the forearm, upper arm, trunk, thigh, and calf segments, and (2) the ratio + length model using actual measurements of the body segments in the ratio model. The models were evaluated using data from 360 lifting trials performed by 10 subjects (5 males and 5 females) with an average age of 51.50 (±9.83) years. The accuracy of the two models was compared against data collected by a laboratory-based motion capture system as a function of 12 ACGIH lifting risk zones and 3 grouped risk zones (low, medium, and high). Results showed that only the ratio + length model provides acceptable estimates of lifting risk with an average of 69% accuracy level for predicting one of the 3 grouped zones and a higher rate of 92% for predicting the high lifting zone.
Background: Magnetic resonance imaging (MRI) is increasingly used to estimate the geometric dimensions of lower lumbar vertebrae. While MRI-based measurements have demonstrated good reliability with interclass correlation coefficients (ICCs) of 0.80 or higher, many evaluations focus solely on the comparison of identical MRI images. This approach primarily reflects analyst dexterity and does not assess the reliability of the entire process, including imaging and image selection. Objective: To evaluate the inter- and intra-rater reliability of the entire process of using MRI to measure biomechanically relevant lumbar spinal characteristics, incorporating imaging, image selection, and analysis. Methods: A dataset of 144 low-back MRI scans was analyzed. Reliability assessments were performed under different conditions: (1) identical scans rated by the same analyst at different times (intra-rater reliability) and (2) distinct scans of the same subject obtained by different MRI operators and analyzed by different analysts (inter-rater reliability). Mean absolute differences in measurements were calculated, and sources of variability, such as breathing artifacts, were noted. Results: Larger discrepancies were observed when comparing distinct scans analyzed by different MRI operators and analysts. In the “worst-case” scenario, where both the MRI operator and analyst differed, a 4.05% mean absolute difference was noted for anterior endplate measurements. This was higher than the 2.76% difference observed when analysts re-rated their own scans after one month. Despite these discrepancies, the variability in measurements was relatively low and primarily attributed to factors like breathing artifacts. Conclusion: The process of using MRI to derive biomechanical measures, particularly for bony structures, demonstrates robust reliability. Variability in measurements is minimal even under challenging conditions, supporting the use of MRI for biomechanical assessments.