Renewable energy has become an essential energy alternative since the continual depletion of non-renewable energy resources and increasing environmental issues. Tidal energy is a promising future renewable resource which can be extracted using a vertical axis tidal turbine. Since it was proposed, a tidal turbine performance requires improvements which can be obtained by a blade’s trailing edge modification. Modifying the blade’s trailing edge profile is confirmed to be one way to improve a turbine’s work. However, the influence of a trailing edge modifications on a vertical axis tidal turbine blade’s interaction with fluid has not been fully understood, thus the fluid induced vibration as the fluid behaviour working on a vertical axis tidal turbine blade has not been completely discovered. In this paper, 2D fluid-structure interactions of modified vertical axis tidal turbine blades are examined and modelled using OpenFOAM. Three different modified blade profiles are proposed: sharp, rounded, and blunt. The modified profiles are employed to an original NACA 0012 blade and their influences on a vertical axis tidal turbine blade interaction are observed. The result discovers the fluid behaviour and fluid-induced vibrations at all positions (represented by 12 positions) over one turbine’s cycle. The results demonstrate the frequency domain blade velocities and time domain blade displacements for all modified blades. The fluid behaviour around the blade is confirmed by pressure distribution plots over the blade’s upper and lower surfaces. The results show that the blunt profile provides less frequent vibrations due to a reducing vorticity in the downstream fluid regime. However, the vibration amplitude that occurs on the blunt blade is higher than those of rounded and sharp profiles. Based on this research, the blunt trailing edge profile appears to be more favourable to be applied and used for vertical axis tidal turbine blades.

A numerical lock-in prediction technique of a NACA 0012 hydrofoil, immersed in a flow having a Re of 3.07x10(6) is proposed in this paper. The technique observes the foil's response as part of a fluid-structure interaction analysis. The response is modelled by foil's vibration which is represented by spring and damper components. The technique identifies and predicts the foil's lock-in when it vibrates. The prediction is examined using the Phase Averaged Method which employs the Hilbert Transform Method. The aim of this paper is to propose a numerical way to identify a lock-in condition experienced by a NACA 0012 foil in a high Reynolds number flow. The foil's mechanical properties are selected and its motions are restricted in two modes which are in the pitch and heave directions. The rotational and transverse lock-in modes are identified in the model. The existence of lock-in is verified using pressure distribution plot, the history of trailing edge displacement and fluid regime captures. The history of total force coefficients are also shown to clarify the result. From the result, it can be shown that the technique can predict reliably the lock-in condition on the foil's interaction. Three main fluid induced vibration frequencies are generated in the interaction. None of them are similar to the foil's natural frequency and the phenomenon of lock-in is apparently not found in the typical operational condition.

Y Solar air heater (SAH) is a renewable energy application for the drying process. SAH has a challenge to produce high performance under uncertain weather. The performance of SAH can be enhanced by providing the absorber plate by adding the fins. This study aims to evaluate the thermal performance of SAH with rectangular fins SAH at low air velocity. This study compares the performance of SAH without fins and SAH with rectangular fins. Two variations of a tilt angle of SAH are 0 degrees and 30 degrees which are observed in this study. The SAH uses a ventilator turbine to suck air into the collector box. The air velocity is 0.01 m/s. The method is experimental. The SAH is tested under real condition from 9 a.m. to 4 p.m. The measurement tools consist of a pyranometer, an anemometer, a temperature sensor in the inlet section, 3 sensors in the absorber plate, a sensor in the outlet section, 6 temperature sensors in the drying cabinet. The result showed the thermal efficiency of SAH with rectangular fins is 29.67 % higher than SAH without fins at 0 degrees tilt of angle at noon. The thermal efficiency of SAH with rectangular fins is 25.26 % higher than that of without fins at 30 degrees tilt of angle at noon.

A steam turbine is the most critical component in a thermal power plant. Due to its crucial function, it should be maintained to be able to operate without failure. This paper aims to develop an application that can be used to analyze the reliability and synchronization of vibrations in a single evaluation through the application. The application is helpful to decide the proper time the maintenance should be performed in order to provide a better maintenance strategy. In this paper, the application was used to make an ease in evaluating the reliability and vibration of a 670 MW power plant steam turbine. The reliability was analyzed by qualitative and quantitative methods. The vibration evaluation using Fast Fourier Transform (FFT) was done by diagnosing the failure symptoms from vibration spectrum. The analysis of synchronization of vibrations conducted by comparing the vibration frequency and the natural frequency of the system which can be calculated easily using the application. The algorithm program of both evaluations was built using GNU Octave software to make a friendly user interface. From the evaluation result, the most critical components of the steam turbine are coupling, labyrinth seals, bearing, diaphragm, turbine control valve, and turbine stop valve. The maintenance interval based on the expected reliability of 90% produces the highest reliability improvement. Based on the vibration analysis, there is no failure symptoms detected in the turbine bearings. Furthermore, the dominant frequencies of vibration are distant from the natural operate.

The offshore jack-up production platform operates in extreme and unpredictable marine environments. Therefore, its structural strength must be designed to withstand harsh conditions, particularly hydrodynamic loads from waves and ocean currents. This study aims to numerically analyze the interaction of marine hydrodynamic forces with a jack-up production platform using OpenFOAM v1606, a Computational Fluid Dynamics (CFD) software. Specifically, the research evaluates a buoyancy-modified k−ω SST turbulence model based on the Standard Gradient Diffusion Hypothesis (SGDH) on a 3D jack-up platform model. The analysis is conducted using a Stokes 5th-order wave model within the waves2Foam toolbox, considering four variations in wave height and period. The results demonstrate that the modified turbulence model provides more accurate predictions. Additionally, they reveal that the forces acting on the platform’s walls are directly proportional to wave height and period, with the highest recorded load reaching 4000 N in Case A, where the wave height and period are 5.4 m and 5.9 s, respectively. Furthermore, it is observed that most of the forces exerted on the platform hull are vertical, primarily due to the negative pressure on the platform’s bottom side.

The depletion of fossil fuels and the worsening environment motivate engineers and researchers to explore renewable energy resources. One of the promising renewable energy is wind energy. The wind turbine extracts wind energy to generate electricity. This study aims to modify a wind turbine blade using Clark Y foil to improve the lift force. The modification is employed by forming a winglet profile with a 30° angle on the foils tip. The result shows that the 30° winglet enlarges the lift coefficient to 1.3253 from 1.2795 of the original blade lift coefficient.