In this study, the effect of the addition of multi-walled carbon nanotubes (MWCNTs), at three percentages, into the urea-formaldehyde (UF) shell-wall of microcapsules on the healing efficiency is reported. The modified shell-wall created a conductive network in semi-conductive epoxies, which led to an improvement of the electromagnetic interference shielding effectiveness (EMI SE); utilizing the excellent electrical properties of the CNTs. The microcapsule’s mean diameter and shell wall were examined via scanning electron microscopy (SEM). Thermal stability was evaluated via thermogravimetric analysis (TGA). The healing efficiency was assessed in terms of fracture toughness, while the electrical properties were measured using impedance spectroscopy. The measurements of the EMI SE were carried out in the frequency range of 7–9 GHz. The derived results indicated that the incorporation of the CNTs resulted in a decrease in the mean size of the microcapsules, while the thermal stability remained unchanged. In particular, the introduction of 0.5% w/v CNTs did not affect the healing efficiency, while it increased the initial mechanical properties of the epoxy after the incorporation of the self-healing system by 27%. At the same time, it led to the formation of a conductive network, providing electrical conductivity to the epoxies. The experimental results showed that the SE increased on average 5 dB or more after introducing conductive microcapsules.

A configurable design of a microstrip square spiral RFID tag antenna, for a wide range of microwave frequencies in S- and C-band, is presented. The design is parameterized in dimensions, and hence changing the design frequency (or frequencies) is easy, by changing only an initial value for the spiral geometry. A tag specimen was fabricated using Cu electroplating technique according to the design for frequencies of interest in the areas of 2.4 and 5.8 GHz. The substrate material is a 320 μm high resistivity Si and the bridge dielectric is a 15μm polyimide PI2525. The microfabrication process involves steps of metallic structure pattern transfer techniques with optical UV lithography procedures. The reflection coefficient and gain of the specimen were measured inside an anechoic enclosure using a vector network analyzer (VNA) and a TEM horn test antenna over a frequency range of up to 6 GHz. Simulated and measured results are presented and discussed, exhibiting reasonable agreement.

A microwave free space reflectometry technique with swept frequency measurements for the profiling of wall structures and the detection of hidden (covered) layers has been applied to the Hagia Sophia byzantine monument. Experimental measurement results are presented and compared with three-dimensional (3D) simulated results, exhibiting fair agreement in some (though not all) aspects. Based on the experimental results, the possibility of clear discrimination between regions with and without covered mosaic layers, and hence the detection of such layers, is demonstrated.

Microbolometer arrays, i.e., arrays of micro-scale pixels sensing temperature via resistance changes, have proven to be an effective basis for real-time imaging instrumentation in infrared as well as terahertz frequencies. In previous work, a design of THz and IR absorbing nano-laminates of dielectric and metal layers was studied. It was shown via numerical modeling that absorption may be maximized by appropriate choices of thickness, permittivity and conductivity. In this work, an analytical approach to the problem is formulated based on the standard recursive multiple reflection formulas for multi-layered planar structures. The results fully confirm and extend previous numerical work. A previous relationship between wavelength and silicon thickness for maximum absorption, derived numerically for specific parameter combinations, is now generalized in a parametric closed form. The method can be extended to include multiple lossy dielectric layers and may serve as a tool for optimizing the absorption characteristics of more complex layered absorbing structures. This could enhance the sensitivity of the detection scheme of interest, providing benefits in terms of cost, efficiency, precision, and adjustability.

A configurable design of a microstrip square spiral RFID tag antenna, for a wide range of microwave frequencies in the S- and C-band, is presented. The design is parameterized in dimensions, and hence changing the design frequency (or frequencies) is easy, by changing only an initial value for the spiral geometry. A tag specimen was fabricated using a Cu electroplating technique according to the design for frequencies of interest in the areas of 2.4 and 5.8 GHz. The substrate material is 320 μm high-resistivity Si and the bridge dielectric is 15 μm polyimide PI2525. The steps of the microfabrication process involve metallic structure pattern transfer techniques with optical UV lithography procedures. The reflection coefficient and antenna gain of the specimen were measured inside an anechoic enclosure using a vector network analyzer (VNA) and a TEM horn test antenna over a frequency range of up to 6 GHz. Simulated and measured results, exhibiting reasonable agreement, are presented and discussed.